Search:

Type: Posts; User: rb99

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 43 minute(s) ago.

  1. Replies
    10
    Views
    3,272

    I got that one. That's in US dollars. It is no...

    I got that one. That's in US dollars. It is no different than the Fedex quote. That will translate into close to $150 Canadian when the courier stops extorting me for brokerage fees, handling fees,...
  2. Replies
    10
    Views
    3,272

    I was hoping to buy one already made and ready to...

    I was hoping to buy one already made and ready to go... SB ships only with Fedex and they want $130CAD to ship a small plate to me.
  3. Replies
    10
    Views
    3,272

    What about software and hooking it up?

    What about software and hooking it up?
  4. Replies
    10
    Views
    3,272

    Tell me more please. What is a CNC corner block?...

    Tell me more please. What is a CNC corner block?

    Thanks
  5. Replies
    10
    Views
    3,272

    WANTED: 3 Axis Zero Plate

    I am looking for a 3 axis zero plate for my SB with a 4G controller.

    Let me know if you have one for sale.

    Thanks
  6. Replies
    17
    Views
    11,410

    With my old controller it had a "motors off"...

    With my old controller it had a "motors off" command and I could manually move the router into it's final position. I had the old ball screw Z. I would put a piece of paper under the bit and turn the...
  7. Replies
    17
    Views
    11,410

    If forgetting the clamp is an issue, perhaps...

    If forgetting the clamp is an issue, perhaps making it with a break-a-way using magnets would help?
  8. Replies
    17
    Views
    11,410

    What I want to do is have a plate or something...

    What I want to do is have a plate or something that allows me to quickly zero the X Y and Z axis'.

    I am not sure which plate you are talking about. Since starting this thread I found the one I saw...
  9. Replies
    17
    Views
    11,410

    Help With 3 Axis Zero Plate

    I am looking for a way to zero the 3 axis on my older shopbot with a 4g controller. I remember there were aluminum plates with a recessed hole that the bit goes into the hole and touches 3 sides and...
  10. Replies
    12
    Views
    5,329

    First it's the screws, next they won't send...

    First it's the screws, next they won't send motors with the router. Then all you'll get is an empty box.
  11. Replies
    12
    Views
    9,788

    Gears are loose on the motor shaft. (?)

    Gears are loose on the motor shaft. (?)
  12. Replies
    5
    Views
    4,598

    A metal detector would be good for finding hidden...

    A metal detector would be good for finding hidden nails.
  13. Replies
    36
    Views
    13,800

    What is your working version?

    What is your working version?
  14. Replies
    36
    Views
    13,800

    Just to cover the bases, have you checked all the...

    Just to cover the bases, have you checked all the pinions and motor mounts?

    Power to the motors? It could be a simple mechanical issue not related to the other stuff.
  15. Replies
    26
    Views
    10,728

    Did you read the article about the fine airborne...

    Did you read the article about the fine airborne particles being like glass shards and just walking in the shop will stir up enough invisible dust to make the air unsafe... What's the rich dc?
    ...
  16. Replies
    26
    Views
    10,728

    After reading about the health risks of the super...

    After reading about the health risks of the super fine airborne dust particulates I am actually questioning whether I should continue to use my CNC equipment. I am not sure about spending $3K-$4K-$5K...
  17. Replies
    26
    Views
    10,728

    When the foot is attached to the router won't any...

    When the foot is attached to the router won't any vibration of the foot cause small but visible movement of the router? For example a piece of cutting flies up and hits the foot or a cutoff piece...
  18. Replies
    3
    Views
    2,371

    I would think 1" or larger. If you use a ball...

    I would think 1" or larger. If you use a ball nose bit you might get something smaller.
  19. Replies
    8
    Views
    6,341

    It's a magic floating tree. Looks fine. I have...

    It's a magic floating tree. Looks fine. I have seen this before and was impressed by the whole sign. I never saw any flaw with the tree. (which rhymes with OCD) :-)

    I don't understand your fix. Do...
  20. Replies
    26
    Views
    10,728

    Why do you want the 5" to the foot?

    Why do you want the 5" to the foot?
  21. Replies
    26
    Views
    10,728

    What about chunks jamming up the hose at the foot?

    What about chunks jamming up the hose at the foot?
  22. Replies
    26
    Views
    10,728

    Is it important to have a large diameter vacuum...

    Is it important to have a large diameter vacuum hose? Are there problems using Shopvac hose? I have little room for the hose...
  23. Replies
    18
    Views
    13,302

    Can I use the belt drives with a 4g box on an old...

    Can I use the belt drives with a 4g box on an old pr with an upgraded Z? If so can I use my same motors?

    Thanks
  24. Replies
    4
    Views
    5,576

    What are the sizes of the shelters? Thanks

    What are the sizes of the shelters?

    Thanks
  25. Replies
    15
    Views
    7,852

    Not sure, just seems like a lot of work and a...

    Not sure, just seems like a lot of work and a great finished piece for that amount.
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4