Gus,
You mention aspire files fo rthis chair.
How would I get a copy?
congdonds@gmail.com
Kind regards
Shaun
Type: Posts; User: shaun
Gus,
You mention aspire files fo rthis chair.
How would I get a copy?
congdonds@gmail.com
Kind regards
Shaun
The McMaster part number I used is 7372T5 on page 1255. I think I might consider going with the shorter bristles of 7372T4 especially if you primarily cut plywood. I do a fair amount of deep relief...
Gene
Send me your email and I will send you the cut files and a part number. I cut the plexi pipe out of the original shroud and tapped the bottom ring clamp holding my router. I had some 10 mm...
Yes that is why I uploaded the dxf. Could not upload the .crv file. My email is congdons@rochester.rr.com
I am planning on using 1/2" Baltic birch. I have not cut any of it yet. i like your idea...
no the file is actually 18 x 31 inches. I am sure there are a lot of open vectors because I was just trying to get it to a point I could show the concept. I actually originally drew it in...
I was thinking I would just use four dowels in my waste board as my incremental locators. I was going to parse my file into four seperate cut files.I created a box that was 9x24 and just pasted them...
Thanks so much for the feedback. Sorry I have not been responding. I only get to visit my shopbot on the weekend and was working on a magnetic dust shoe in the mean time.
I have been trying to find a thread that gives creative ideas on how to make a piece longer than my 18x24 working space on my dektop unit by indexing the material through. Seems like I should be...
turns out their is not a newer version of partworks 3D so you cannot copy the database and make them the same if you update your partworks software. I ended up manually recreating all of the tools...
Adrian,
Thanks for the help. I did find the tool database as you described. Unfortunately I copied in the database from partworks and got the following error message.
Error: tooldatabase written...
I just updated my software and my tool databases are different. I can not seem to find the correct file for partworks 3D. I even tried deleting what I thought was the tools.tool_db file but it...
I updated my software and am having trouble getting partworks and partworks 3D to have the same tool databases.
Anybody know exactly where I need to copy the file to make the two match?
Adrian,
I figured out what you were talking about. I am not the brightest sometimes.
Thanks a bunch.
regards,
shaun
Adrian,
Thanks for the answer
I do not have this file "ToolDatabase_locations.txt" on my hard drive.
I do not have a tool database folder anywhere in the partworks folder. I do in the others.
I...
My partworks and partworks 3d have different tool selections. How do I make them the same? The partworks 3d and SB3 both have a file that says tool.tool_db with different file sizes. I cannot find...
Brady,
I think you nailed it again. My step over was .625 instead of .0625. I did not conciously set it. I need to learn each of these functions better. I have probably never used that bit...
Brady,
The two pieces of foam represent the STL import file and one I created in partworks. The little piece is what the end result is supposed to look like.
Brady,
I will definately need to read up on VR. It seems to have fixed the stutter and loosing zero. Unfortunatley, I seem to have a new issue. The file is not cutting as the preview shows. I...
Ok, will try cutting it tomorrow.
The actual job is 10 x 18 x 3. I was planning on cutting it in foam to see if anything hits.
The practice piece is a 4 x 4 x 1 block with a 3 inch hole 3/4 deep....
Brady,
I chose 3 inches per sec for feedrate and 2 inches per second for plunge.
The VR xyMove speed is .4
The ZMove Speed is .4
move ramp rate is .15
slow corner speed is 65
3d ramp...
I created a file in solidworks and saved as an stl. I imported it into partworks 3d and created a tool path. When I run the file the first pass seems to cut ok but when it steps down to make the...