Search:

Type: Posts; User: srwtlc

Page 1 of 20 1 2 3 4

Search: Search took 0.34 seconds.

  1. Ok, got ya. That wouldn't be so much a postp...

    Ok, got ya. That wouldn't be so much a postp situation as it would be a software recognition of say a "Pod" layer where when choosing to add tabs, it would avoid that overlapped area. That might be...
  2. Not quite understanding the need for a custom PP...

    Not quite understanding the need for a custom PP either, when Vectric products have tabbing options built into the profile toolpath.
  3. Replies
    2
    Views
    772

    Sorry, but this was sold. Sold via a different...

    Sorry, but this was sold. Sold via a different thread and a PM and I forgot to find and mark this as sold.
  4. Replies
    10
    Views
    723

    More info in your other thread on the same...

    More info in your other thread on the same subject, with files and instructions needed to make it work. There are also files in the sbparts folder that you can learn from and adapt to work with one...
  5. Possibly for the mechanical hard stops.

    Possibly for the mechanical hard stops.
  6. Replies
    2
    Views
    329

    Probably be easier to find a parallel port add in...

    Probably be easier to find a parallel port add in card of some sort.

    Better question is why do you need it? 😉
  7. Replies
    12
    Views
    1,153

    Sneak up on it with the keypad after getting it...

    Sneak up on it with the keypad after getting it close....

    "Several additional functions are provided. If you hit a <D> (upper or lower case) on your keyboard or click on the “fixed” button in the...
  8. Replies
    12
    Views
    1,153

    This should get you started. You can modify to...

    This should get you started. You can modify to suit your needs.

    https://1drv.ms/u/s!AsPqyLrhnhkRgzmUXrkRdRXNNVGq?e=dnJMAO
  9. Replies
    3
    Views
    697

    Been off SB3 for so long now that I can't...

    Been off SB3 for so long now that I can't remember, but it seems like there was a version somewhere along the line that did that. It doesn't seem likely, but there's a dwell setting in the hole...
  10. Replies
    12
    Views
    835

    Just in case if this happens to be a new software...

    Just in case if this happens to be a new software setup, be sure to run Tools/Shopbot Setup to set the offset for the second Z. Just follow the prompts and instructions to work through it.

    If you...
  11. Replies
    1
    Views
    414

    Might want to specify what control box you have,...

    Might want to specify what control box you have, what VFD, and the version of SB3 you're running.

    I have one of the USB spindle rpm controllers for sale if needed, it uses RS485 communication...
  12. Replies
    4
    Views
    526

    While the other guys have covered your query from...

    While the other guys have covered your query from the Aspire side, it sounds like you could just make one design with the toolpaths for it and then create a master file (.sbp) that would call up the...
  13. Quartersawn and tighter growth rings will be more...

    Quartersawn and tighter growth rings will be more stable and cut cleaner. Flatsawn, especially if you glue up the full width of the 10" will guarantee that your panel will cup, even if you alternate...
  14. Replies
    55
    Views
    26,445

    :p Scott, yup, full of my mornin' coffee and...

    :p Scott, yup, full of my mornin' coffee and feelin' a bit snarky, but the question was "how to cut a top that is larger than what will fit on the Desktop". So, the first thing that came to mind was...
  15. Replies
    55
    Views
    26,445

    Perhaps you're missing a table saw, circular saw,...

    Perhaps you're missing a table saw, circular saw, jig saw, or one of those that you operate by hand. ;)
  16. Replies
    2
    Views
    1,104

    Runs in my browser and you can generate a file. ...

    Runs in my browser and you can generate a file. http://gofabmo.org/fabmo-hershey-app/
  17. Good job, glad you got it worked out! What was...

    Good job, glad you got it worked out! What was your error, just a little syntax?

    It wasn't for nothing, someone else may come across a similar situation and now there's answer.
  18. Replies
    15
    Views
    1,601

    Assuming that you were using a Vectric product,...

    Assuming that you were using a Vectric product, when you choose a post processor to save a toolpath, one of the posts in the list used to be named ShopBot_inch (or something similar) and that one...
  19. Replies
    15
    Views
    1,601

    Grab the nose of the spindle and give it a...

    Grab the nose of the spindle and give it a push/pull in the long axis and feel for play in the lower v-bearings of the Y car. There should be no play in it. Check for play due to the motors/pinions...
  20. Could you set a variable (True/False) when you...

    Could you set a variable (True/False) when you are doing multiples or not and then check for it?

    Turn on a unused output and check for it with %101-%108 and show a msgbox if needed. Turn it off...
  21. Have you looked at the VO command... VO -Value...

    Have you looked at the VO command...

    VO -Value Temporary Tool Offset {Activate Offset, Offset-X, Offset-Y, Offset-Z, Offset-A, Offset-B, Offset-C}

    This command turns on or off a temporary...
  22. Replies
    21
    Views
    3,731

    Guessing he got halfway through and ran out of...

    Guessing he got halfway through and ran out of gas!? :D
  23. Replies
    21
    Views
    3,731

    Like this little guy! ;) ...

    Like this little guy! ;)

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=33979&stc=1
  24. Good grief, you're running out of forums (I've...

    Good grief, you're running out of forums (I've seen them all) to post your sour grapes on Jerry and it's gotten tiresome! Give it up, get over it, and move on already!! :mad:
  25. Replies
    2
    Views
    354

    Use 3D tabs, but maybe increase the length...

    Use 3D tabs, but maybe increase the length slightly to add some strength to it due to the fact that it ramps up to the 0.125" height instead of going straight up. Keep in mind that the actual tab...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4