Search:

Type: Posts; User: willmorgan

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    3,640

    Very Nice!!!! Would love to make one of these.

    Very Nice!!!! Would love to make one of these.
  2. Wow, great post Steve, but of course I wouldn't...

    Wow, great post Steve, but of course I wouldn't expect nothing less. That is very helpful information.

    Will
  3. Thread: new ride!

    by willmorgan
    Replies
    6
    Views
    1,895

    Great buy, I have an 8' bed as well and about...

    Great buy, I have an 8' bed as well and about 230000 miles on the 2001 Diesel. It will treat you well! Congrats.
  4. Replies
    13
    Views
    3,783

    I use a Onsrud 63-718 and cut in one pass.

    I use a Onsrud 63-718 and cut in one pass.
  5. Replies
    32
    Views
    10,191

    Not sure about everybody else but I find myself...

    Not sure about everybody else but I find myself always wishing I had more drive in doors, lots of drop down power and air!
  6. Replies
    6
    Views
    1,872

    Darn, next time let me know maybe we could just...

    Darn, next time let me know maybe we could just meet somewhere for some good food!
  7. Replies
    6
    Views
    1,872

    Hey Gene, There is someone on here that is a...

    Hey Gene,
    There is someone on here that is a teacher at a school in Charlotte, if you can find him, I sure that would ge a great visit. I'm in Winston-Salem but would be just a little out of the...
  8. Replies
    2
    Views
    823

    Thanks Bob, That may be what I have to do.

    Thanks Bob,
    That may be what I have to do.
  9. Replies
    2
    Views
    823

    files for equipment

    Hello all,
    I am wanting to create some edge lit acrylic signs using equipment like dozers, motor graders and etc.

    Anyone have a good site where I could get the files.

    Thanks for your help.
  10. Thread: Stepover

    by willmorgan
    Replies
    13
    Views
    3,405

    Joe, That really wasn't a question, I was just...

    Joe,
    That really wasn't a question, I was just explaining why I asked the question.

    However I will post a pic tomorrow when I get back to the shop, maybe you all have see it before. I know the...
  11. Thread: Stepover

    by willmorgan
    Replies
    13
    Views
    3,405

    very nice guy's, thanks for sharing. I was...

    very nice guy's, thanks for sharing.

    I was cutting 1/4 aluminum and was getting a small step and just wondered it that could have been the issue.
    I don't know, maybe I'm getting a small bit of...
  12. Replies
    10
    Views
    5,055

    Very nice, thanks for sharing both of you!

    Very nice, thanks for sharing both of you!
  13. Thread: Stepover

    by willmorgan
    Replies
    13
    Views
    3,405

    Thanks for the help. I thought that was the...

    Thanks for the help. I thought that was the answer but wanted to check. I have look for it but everything talks about 3D or pocket.
    I find myself going back to the tutorials a lot.
    I am going to...
  14. Thread: Stepover

    by willmorgan
    Replies
    13
    Views
    3,405

    Stepover

    When making a profile cut with multiple passes, does the software ignore the stepover value?
  15. Replies
    1
    Views
    736

    Never mind, I got it. Sorry all.

    Never mind, I got it. Sorry all.
  16. Replies
    1
    Views
    736

    Issue with ramp

    Well hello all, it's me again with another issue.

    I have added a ramp to my tool-path but it is not ramping. I tested it last night with a straight line and it worked fine. Can anyone tell me...
  17. Replies
    12
    Views
    3,749

    Very nice job Steve!

    Very nice job Steve!
  18. Thread: Cost

    by willmorgan
    Replies
    8
    Views
    4,302

    Byron, I have BobCam V27, I really don't use it....

    Byron,
    I have BobCam V27, I really don't use it. How do you like it compared to Aspire and Fusion 360?
  19. Replies
    7
    Views
    3,535

    Say it ant so Dave! You getting out of the...

    Say it ant so Dave! You getting out of the business?
  20. Replies
    26
    Views
    7,819

    Well all, the stronger motor fixed the Z, it now...

    Well all, the stronger motor fixed the Z, it now keeps the 0 all the time. Thank you everyone for your help on this, however now that I have the Z fixed I now have another issue. I am cutting foam...
  21. Replies
    26
    Views
    7,819

    I checked that Bill, it's not hitting the stop. ...

    I checked that Bill, it's not hitting the stop. In doing some research and talking to SB, they recommend the stronger motor. I will keep you all posted.
  22. Replies
    26
    Views
    7,819

    I reset the ramp settings and tried again. The...

    I reset the ramp settings and tried again. The video above is with the new settings.
  23. Replies
    26
    Views
    7,819

    Here is a video of the issue. It's at the end of...

    Here is a video of the issue. It's at the end of the video where it is rounding out of the letter.


    https://youtu.be/3LOsP4qSA38
  24. Replies
    26
    Views
    7,819

    Top of the material.

    Top of the material.
  25. Replies
    26
    Views
    7,819

    The Z axis moves fine. I have had the updated...

    The Z axis moves fine. I have had the updated control box on for about a year now. So just updated the spindle.

    My values don't look anything like what you said. See attached. You think this...
Results 1 to 25 of 80
Page 1 of 4 1 2 3 4