Search:

Type: Posts; User: archis

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Issue with Tabs

    by archis
    Replies
    9
    Views
    3,676

    I'm noticing my issue on .7 to 1 inch oak with...

    I'm noticing my issue on .7 to 1 inch oak with .125 h x .25 w inch tabs. My buddy probably has about 25 hours on it.
  2. Thread: Issue with Tabs

    by archis
    Replies
    9
    Views
    3,676

    Does anybody have any photos of a Brady vac setup...

    Does anybody have any photos of a Brady vac setup with a buddy?

    I'm looking for better ideas than mine, which was an elevated platform for the brady van with the vac hose on top of my standard...
  3. Thread: Issue with Tabs

    by archis
    Replies
    9
    Views
    3,676

    Maybe a little extra sanding isn't so bad after...

    Maybe a little extra sanding isn't so bad after all:)
  4. Thread: Issue with Tabs

    by archis
    Replies
    9
    Views
    3,676

    I'm glad its not me, I just wanted to be sure...

    I'm glad its not me, I just wanted to be sure there wasn't a problem with my buddy.
  5. Thread: Issue with Tabs

    by archis
    Replies
    9
    Views
    3,676

    Issue with Tabs

    I'm having an issue with tabs in that wherever I place a tab I get a slight groove in my part as the spindle lifts up to cut the tab. This groove requires sanding on an otherwise clean edge.

    I've...
  6. Replies
    17
    Views
    6,857

    Thanks everyone, I get it now. I'll get a...

    Thanks everyone, I get it now. I'll get a compression bit and start experimenting.
  7. Replies
    17
    Views
    6,857

    Is the climbing cut an option I set in Partworks...

    Is the climbing cut an option I set in Partworks when I generate the toolpath?
  8. Replies
    17
    Views
    6,857

    Thanks Guys as usual lots of great advice! ...

    Thanks Guys as usual lots of great advice!

    I do need a couple of clarifications:

    Steve,

    What should I be listening for to find the "Sweet Spot".

    Don,
  9. Replies
    17
    Views
    6,857

    I have no experience with getting clean cuts on...

    I have no experience with getting clean cuts on plywood:D

    Could you recommend some compression bits? I'm not clear on exactly what they are.

    Thanks
  10. Replies
    17
    Views
    6,857

    Cherry plywood machining advice needed

    I have a partition project in the near future that will need to be cut from 1/2 inch cherry plywood. It will need to have a very clean cut since both sides and the cut edges will be visible.
    ...
  11. Replies
    8
    Views
    3,811

    Gary, I'm not sure how a ramp speed bug could...

    Gary,

    I'm not sure how a ramp speed bug could be the issue here. If I set my tools plunge speed to be the same as the feed rate, I don't see the issue. That seems to be telling me that the...
  12. Replies
    8
    Views
    3,811

    Gary, I'm running Version 3.6.32. Brady,...

    Gary,

    I'm running Version 3.6.32.

    Brady,

    My VR is set to .4

    Thanks,
    Jim
  13. Replies
    8
    Views
    3,811

    Dana, Sorry I meant Inches per Minute. Try...

    Dana,

    Sorry I meant Inches per Minute. Try it yours, I'll bet you'll get the same results, unless of course I'm behind on a control software update :D
  14. Replies
    8
    Views
    3,811

    OK I think this is a bug. When experienced...

    OK I think this is a bug.

    When experienced the problem I had my tool configured as

    Feed Rate 90 In/Sec
    Plunge Rate 15 In/Sec

    If I modify my tool to
  15. Replies
    8
    Views
    3,811

    Strange Buddy Issue

    I've noticed for a couple of weeks that my Buddy seems to slow to a crawl at certain unexpected times. I've attached a snippet a file that is currently giving me trouble.

    Do anyone have any...
  16. Replies
    3
    Views
    2,250

    Thanks Gary that was it. I thought it would...

    Thanks Gary that was it.

    I thought it would yell at me if the vector was open and I tried to generated a toolpath, I guess that's not always the case.
  17. Replies
    3
    Views
    2,250

    Partworks 3.091 Bug

    Has anybody experienced a bug in partworks 3.091 where the machine vectors for profile cutting are swapped?

    If I select outside, it cuts inside (and diagrams inside), and if I select inside it...
  18. Replies
    19
    Views
    8,345

    Thanks Brady, that helped to put things in...

    Thanks Brady, that helped to put things in perspective.

    Reliefs are a big part of what we want to do since my wife is interested in fabric printing which will involve carving a lot of plates.
    ...
  19. Replies
    19
    Views
    8,345

    I looked at Aspire and I'm also looking at Rhino....

    I looked at Aspire and I'm also looking at Rhino. I think aspire is about twice the price of Rhino, does it have any advantages over Rhino?

    From what I've seen of Rhino so far, it looks pretty...
  20. Replies
    19
    Views
    8,345

    Thanks but I think that's 2d, I'm looking for a...

    Thanks but I think that's 2d, I'm looking for a 3d package that's "sorta like" partworks. The sketchup paradigm isn't working for me.
  21. Replies
    19
    Views
    8,345

    I'm trying to find a 3d package that works for...

    I'm trying to find a 3d package that works for me. I have tried Sketchup but I'm not convinced its for me.

    I really like aspects of partworks, especially how it lets me draw polylines by ...
  22. Replies
    4
    Views
    3,444

    Will do, Thanks!

    Will do, Thanks!
  23. Replies
    4
    Views
    3,444

    3D Starter Carving Bit

    I would like to try my hand as some simple 3d carvings. What's the best general purpose bit to get my feet wet with? Thanks
  24. Replies
    9
    Views
    4,468

    Moroccan Bow Lathe

    For all of you off the grid turners out there:)



    http://www.youtube.com/watch?v=wnv0DAR_gWA
  25. Replies
    2
    Views
    5,654

    Thanks Gary, now it makes sense.

    Thanks Gary, now it makes sense.
Results 1 to 25 of 107
Page 1 of 5 1 2 3 4