Search:

Type: Posts; User: rww

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    1,503

    That sounds like a good plan. Thank you. I will...

    That sounds like a good plan. Thank you. I will do some homework and dry runs first. Thanks again for your suggestion!
  2. Replies
    6
    Views
    1,503

    Thanks. But part works automatically changes the...

    Thanks. But part works automatically changes the spiral tool path to a zig zag ramp when I add any leads.
  3. Replies
    6
    Views
    1,503

    Trouble with internal threads

    I am trying to cut some internal threads. I'm using partsworks 2.5 with a spiral toolpath. Everything works fine except when the cut is finished. When the tool pulls up it cuts a notch up the side....
  4. Thread: my vacuum lift

    by rww
    Replies
    17
    Views
    13,326

    There are two switches in the box. One turns the...

    There are two switches in the box. One turns the vac on and the other one is the up and down for the winch.
  5. Replies
    5
    Views
    1,423

    I'm sure someone with more knowledge than me will...

    I'm sure someone with more knowledge than me will reply. But I think it would be cheaper to buy a generator than buy a UPS that big ( if they even make one large enough)
  6. Thread: Painting Corian

    by rww
    Replies
    4
    Views
    1,179

    I made a address sign for my house about 4 years...

    I made a address sign for my house about 4 years ago. It is installed outside in the weather. I didn't prime it. I just used a cheap spray paint and it still looks new today.
  7. Replies
    10
    Views
    2,740

    Is there any way to use these files with part...

    Is there any way to use these files with part works 2.5?
  8. Replies
    4
    Views
    2,086

    I don't have the full specs in front of me. 2 gig...

    I don't have the full specs in front of me. 2 gig of ram I believe.
  9. Replies
    4
    Views
    2,086

    Computer died. Starting over!!!!

    Computer crashed and I'm trying to set up another one. I have a PRS Alpha 120x60 with one of Gary Campbell's ARO air drills.

    I have my custom files from Gary C. backed up.
    But some thing/things...
  10. Replies
    9
    Views
    5,461

    I have used the eliminator chuck on a router...

    I have used the eliminator chuck on a router table. It worked ok with small bits but had vibration issues with larger bits.
  11. Thread: my vacuum lift

    by rww
    Replies
    17
    Views
    13,326

    Here is the vac that I already had. I would think...

    Here is the vac that I already had. I would think almost any kind of high hg vac would be fine. Either venturi or vac motor.
    ...
  12. Replies
    0
    Views
    1,549

    Why is my Partworks 3D is messed up?

    I haven't used partworks 3D in a long time and wanted to get back into some 3d parts. I went through the usual steps to make the roughing and finishing tool paths and saved those. But when I try and...
  13. Thread: fly cutter

    by rww
    Replies
    10
    Views
    2,379

    I use a 2 1/2" bottom cutter from magnate.net ...

    I use a 2 1/2" bottom cutter from magnate.net

    http://www.magnate.net/index.cfm?event=showProductGroup&theID=136
  14. Replies
    6
    Views
    1,991

    I was able to pull them out with some pliers and...

    I was able to pull them out with some pliers and a slight counterclockwise turn.
  15. Replies
    9
    Views
    2,422

    Can you send me a part works file?

    Can you send me a part works file?
  16. Replies
    9
    Views
    2,422

    I'm about 1.5 hrs east of Tulsa if you can't find...

    I'm about 1.5 hrs east of Tulsa if you can't find anyone closer.
  17. Replies
    5
    Views
    1,379

    I have two 10 footers with no problems for over a...

    I have two 10 footers with no problems for over a year.
  18. Replies
    3
    Views
    1,533

    Thanks Brady. I'm pretty sure It is fully...

    Thanks Brady. I'm pretty sure It is fully engaged. I can visually see the gear rotate instead of just wiggle in the teeth of the gears. Maybe it is the motor getting old. I do have another motor that...
  19. Replies
    3
    Views
    1,533

    X Axis gear box replacement?

    I have a three year old 120x60 prs alpha with a spindle. I have started to notice some play in the x axis on one side. I ordered new pinion gears. Upon further inspection one of my x axis motors will...
  20. Replies
    3
    Views
    2,623

    I have the same problem. I doesn't do it on...

    I have the same problem. I doesn't do it on baltic birch ply. I take a block and send the edge if I am going to edgeband with a thin edge.
  21. Replies
    15
    Views
    5,033

    For small parts like blocks I like to fasten a...

    For small parts like blocks I like to fasten a piece of plywood on the table. Then cut holes the size of the blocks, Insert blocks and you know exactly where center is.
  22. Thanks again Gary. Worked great!

    Thanks again Gary. Worked great!
  23. How to transfer all my settings ect. to new computer?

    I have all my settings where I like them for E cabinets and the link. What is the easiest way to transfer them to a different computer? I think I can use a memory stick but I tried once and didn't do...
  24. Replies
    0
    Views
    1,455

    Where is partworks 2.5 upgrade?

    I have four different computers with partworks. I only upgraded two of them to version 2.5. Now I can't find the upgrade again. Where is it hiding??? Thanks.
  25. Replies
    7
    Views
    2,887

    Thanks Gary. I tried the concrete dye and it...

    Thanks Gary. I tried the concrete dye and it worked great! Carved 51 post painted and delivered in one day. Thanks again.
Results 1 to 25 of 83
Page 1 of 4 1 2 3 4