Just out of curiosity , how much you guys are paying this days for a sheet of birch ?
NZ is over 220 $NZ ;o(
Type: Posts; User: dan78
Just out of curiosity , how much you guys are paying this days for a sheet of birch ?
NZ is over 220 $NZ ;o(
I have a laptop Toshiba 1 year old with Windows 7 home edition CPU Intel 2.20GHz and 8 Gb mem, What I have done step by step Control Pane , > Mobility center > Batery status > High performance ,...
I am using laptops , and I have no problem with the old software , I am pretty close with the new one.
I think the idea of disabling on the bios the power control software is very good , i will...
Hi Jerry ,
just read your post , so basic , now because I could see fixed the "Packet ET" problem , and I am sure is related purely to the USB power , what is left is the CPU ...
Are you...
hi guys
Just post a bit unclear on another post , I will explain , and try to be a bit more clear here again.
I have done the upgrade of the control software and I have experienced all this...
Hi Guys ,
I have done the upgrade , and without any "control" /or / proper understanding of the situation I have most of the problems what where here, or on another threads experienced, so I have...
Thank you very much for you answer, I will have a look around, and once I find something what I think will work I will try to ask again your opinion. ;o)
Cheers DAN
So if I can find something close with 190CFM ..that would be a good start ?
Hi Brady,
Thanks again for your fast answer, I have already a read on this projects, and I will have a bit more.
The problem is I am here down under in Gordonton New Zealand , and if you guys...
For who would may be interested to know.
My initial question to this post was related to the motors, and Brady help me to figure out how things are there, thank you very much again for that help....
Hi guys,
Vacuum again ;o)
Would you like please to look to this pump specs, and let me know what you think.
http://www.vabs.co.nz/side-channel-blowers/284-scl06-02kw1p.html
Okay ...
Basically is not much than a "shopvac" ...only bigger and noisy , I still need about 4 of them to make something decent ...
Hi guys,
I will write here with another problem …
The very beginning now is gone …and obvious for a very nice cut …very important to secure well the material on the table.
Actually after...
I fell I need to say “Sketchchair” big promises , never delivered …used in a very bad way the open source concept.
Thanks for your advice guys ;o)
I have followed Steve's advice last night, and the results are GREAT !!!! I still can see a difference, just because I think I am a bit extreme ;o) The difference...
Okay , then i will try to make the diagonals equal.
Many thanks again for the fast answers, I will be back with the result tomorrow ;o)
Cheers DAN
Yes that is correct, I will re-do the test tonight NZ time following your advice.
What is a result what you will consider okay ? Would you accept any marge of error ?
Thanks again for your...
Hi Steve,
Thank you for you fast answer.
I am using a bit made here in NZ , the first on this list from the producer web page.
http://www.linbide.co.nz/product.php?p=1
I think I get...
Okay ...I manage to have all done and start.
I start cutting with a very large rectangle to check the diagonals.
First try I have a error of 3mm, stop all, push up and down the gantry ,...
Thanks for help Brady , including this
" Reverse the green & black wires in either end of the Wago connector on EACH X axis. Make sure control box is OFF. "
from a different thread ;o)
My...
Okay , and again many thanks ;o) I will let you know how go later ;o)
Cheers DAN
Yes , you are right ;o) I was thinking to shrink tubing ;o)
Okay then , tomorrow I will connect the motors, and the control box, and give a run to hear how sounds ;o) maybe I can do even same dust...
Thank you very much for your fast answer ;o)
I was not very clear with my question , but you nailed right ;o)
Basically if later a problem will require to unplug the motors ...we need to cut...
Hi guys,
I just receive my SB Standard, and start to set him up ;o)
I would like to ask , how are you guys disconnecting the motors on PRS Standard control box. The cables came from the box...