Search:

Type: Posts; User: Red F

Page 1 of 4 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Hole not round

    by Red F
    Replies
    7
    Views
    593

    I found when I was running my router with a climb...

    I found when I was running my router with a climb cut on small holes at high feed rate, my holes looked like yours. I had a little slop in the machine like bill.young just talked about and the climb...
  2. I'm sorry that I am no help answering your...

    I'm sorry that I am no help answering your question, but I am curious about your vacuum setup. I'm trying to work out some vacuum workholding form my machine and I wonder, are each of your pods...
  3. Replies
    5
    Views
    784

    Just from what I remember looking at the one I...

    Just from what I remember looking at the one I used to own. I believe that if you run your table too far back, it bumps into that bolt and kicks the stepper motor out a tiny bit so that it doesn't...
  4. Replies
    11
    Views
    1,267

    Thank you for the clarification Eric. I...

    Thank you for the clarification Eric. I appreciate it.
  5. Replies
    11
    Views
    1,267

    Thank you Eric for the recording of the Webinar. ...

    Thank you Eric for the recording of the Webinar.

    I played with the calculator a little bit and one thing I am a little confused on is the relationship between depth of cut and chipload. It is...
  6. Thread: Table legs

    by Red F
    Replies
    13
    Views
    1,306

    Reminds me of this old thread. ...

    Reminds me of this old thread. http://www.talkshopbot.com/forum/showthread.php?24604-White-oak-table

    He was building 4 sides for each leg and mitering them together
  7. Replies
    4
    Views
    1,081

    One possibility is that your bit isn't truly 120...

    One possibility is that your bit isn't truly 120 degrees or 90 degrees. That would cause over-cutting in the corners like you see on the body of the "I". You can test out cutting some sample...
  8. Thread: 4x8 prt standard

    by Red F
    Replies
    12
    Views
    4,486

    I'm guessing it is in Cookeville TN

    I'm guessing it is in Cookeville TN
  9. Thread: Is CNC cheating?

    by Red F
    Replies
    25
    Views
    6,322

    I know I'm kind of a smart ass, but I named my...

    I know I'm kind of a smart ass, but I named my router "Hand". Got around that "hand made" problem.
  10. Replies
    9
    Views
    2,065

    Eric, that model is great and I'm digging that...

    Eric, that model is great and I'm digging that table you have the model on. We are setting up a new to us non-blue CNC at work and I need to build an off-load table for it. I think I'll try to do...
  11. Replies
    14
    Views
    4,747

    It looks like the tool path is not set for a 60...

    It looks like the tool path is not set for a 60 degree bit, or your z is not zeroed correctly.
  12. Replies
    24
    Views
    5,457

    I bought a Makita track saw to save a little...

    I bought a Makita track saw to save a little money over the festool. The quality wasn't good enough for me, so I sent it back and bought the smaller Festool corded saw (TS55?). I couldn't be...
  13. Thread: Collet help

    by Red F
    Replies
    9
    Views
    1,830

    precise bits has a 1/8" collet and nut for some...

    precise bits has a 1/8" collet and nut for some router models.

    https://www.precisebits.com/gateways/ColletsNutsHome.htm
  14. Replies
    9
    Views
    3,369

    Appears to be a standard. There is red on the z...

    Appears to be a standard. There is red on the z axis motor
  15. Replies
    27
    Views
    8,531

    http://www.talkshopbot.com/forum/showthread.php?19...

    http://www.talkshopbot.com/forum/showthread.php?19903-Buddy-BT48-Alpha-table-MKIII&highlight=buddy+table

    Check out this thread. This is a great aluminum vacuum table built on a Buddy.

    Truely...
  16. Replies
    16
    Views
    4,385

    Brady, Iím trying to picture how a dial indicator...

    Brady, Iím trying to picture how a dial indicator can be used to true up the z-axis without something to offset it like the aforementioned shiny object.
    Would you mount it to the table and chuck a...
  17. Replies
    4
    Views
    2,505

    This has been sold and driven halfway across the...

    This has been sold and driven halfway across the country
  18. Replies
    23
    Views
    6,181

    It may be your surfacing pass and not your second...

    It may be your surfacing pass and not your second cut.

    Could a dull surfacing bit cause push itself up as it cut, or push the table material down?

    When I'm problem solving, I try not to take...
  19. Replies
    4
    Views
    2,505

    Sale pending.

    Sale pending.
  20. Thread: IBILD.com

    by Red F
    Replies
    21
    Views
    15,543

    That is a constant battle for our website guy at...

    That is a constant battle for our website guy at work. I happily only know a little about it.
  21. Thread: IBILD.com

    by Red F
    Replies
    21
    Views
    15,543

    I looked at the site on an Iphone SE. Some of...

    I looked at the site on an Iphone SE. Some of the section title words have to go onto multiple lines due to their font size and length. Also the animated typing bit at the end causes the FAQ part...
  22. Replies
    4
    Views
    2,505

    2008 Buddy 32 standard for sale

    Iím putting my 2008 Buddy 32 standard up for sale. Iím asking $5000 for it. I bought it from the original owner in 2011. In both of its lives it has seen minimal use. The first owner was a...
  23. Replies
    35
    Views
    7,421

    I'm pretty sure that is what he meant by bending...

    I'm pretty sure that is what he meant by bending it into a "z"
  24. Replies
    7
    Views
    5,803

    Something like this? Its home made. Skip ahead...

    Something like this? Its home made. Skip ahead to about the 9:30 mark

    https://www.youtube.com/watch?v=_dGNyc1kHAw
  25. Judging by Craigslist, Tampa Florida

    Judging by Craigslist, Tampa Florida
Results 1 to 25 of 94
Page 1 of 4 1 2 3 4