I've made a 2d cutting toolpath for a sheet of plywood that will ultimately be assembled into a piece of cabinetry. Instead of going back into Fusion 360 to generate a mirrored version of the...
Type: Posts; User: groucho
I've made a 2d cutting toolpath for a sheet of plywood that will ultimately be assembled into a piece of cabinetry. Instead of going back into Fusion 360 to generate a mirrored version of the...
I am having trouble getting the dog bone fillet to work consistently on my pocket boundary conditions. I suspect this is because some lines that are essentially straight are considered arcs by the...
Hi Steve.
Thanks. I just reinstalled the motor a second time. This time I moved it side to side a bit before reattaching it to make sure it was properly seated in the rack and it seems much...
Trying to figure out how to get rid of a rattle on one side of my ganty. See videos below. Any help is appreciated.
https://youtu.be/5CF7DEGoFk0
https://youtu.be/QrHRfNEwyxQ
I would like to “slide” my Shopbot over 4’ on a relatively smooth concrete floor. How would I best accomplish this? Should I remove the gantry first and then simply slide it over with the help of a...
I've been reading that a Shopbot PRS ideally runs on a PC computer with at least 4GB of RAM (8 being better) and a Dual Core Pentium Processor. I've also read that you want to have at last two USB...
I've installed the latest shopbot software on my Dell LatitudeD520 Laptop. After upgrading the ram, I've run the shopbot off this machine in the past. Now that I have upgraded to Windows 10 I don't...
I attached an image of the type of cuts I'm trying to make with this tapered bit. The overall slot depth is about 3/8". Is it recommended to make a cut this deep in one pass with a tapered bit that...
Can anyone give a recommendation for maximum cut depth for a tapered 2 flute upspiral ball bit into a Birch Plywood Sheet?
The link to the bit specs can be found here:
...
I have compression spirals too but my present project doesn't require them. Hoping I can get away with the down spiral. i might try shorting the peck since the down spiral probably increases the...
I work a lot with 1/2" latvian birch plywood and I often need to make a hole that is a 1/4" diameter. I'm often making several pocket and contour cuts with a 1/4" down spiral endmill at the same...
I'm having some issues with a toolpath that I wrote in Fusion 360 tonight. I've attached it here along with a picture of how it failed. It stopped mid routine abruptly (there was kind of a thud). ...
I'm having a similar problem. On previous files I've tried adding the S0,1,1 command to get things started with some positive resulsts but I see from previous successful toolpaths I've run...
I've been trying to get some G-Code from Fusion 360 to work and I see elsewhere in this forum that inserting the SO,1,1 seems to remedy the issue with a dead spindle. However, when I review...
Thanks for this last piece of golden wisdom. Since I'm pretty new to G-Code maybe you could clarify for me what you mean by "the end". Is this insertion of SO,1,0 before or after the end statement. ...
Could someone give me some guidance on how to alter fusion 360 G-code to work with my PRS standard shopbot. My spindle is not turning on. I thought I read a post on this forum previously but I can't...
A little more information...Still trying to figure out what the main issues are here. I seem to have the machine up and running again after deleting the spindle folder as recommended in this post:
...
I've just made the switch to Fusion 360 and I'm having a couple issues. First, I discovered I had to insert the "SO,1,1" into the G Code to get my spindle to turn on. I'm not sure if there is more I...
29505
Interesting. That is actually very similar to what I'm working on (see fusion rendering above) and would be very interested in any wisdom you have to share. That plug idea is great! Wish...
I've just made the switch to Fusion 360 and I'm having a couple issues. First, I discovered I had to insert the "SO,1,1" into the G Code to get my spindle to turn on. I'm not sure if there is more...
29498
I do have a tablesaw and I was worried about the imprecision of the tall vertical cut but I take your point. Much more expedient and I can always measure things with the calipers and take...
Sorry I wasn't clear. I AM using a 1/2" bit.
I laminated several sheets of rectangular 1/2" marine plywood sheets together to form a 3 1/2" thick slab. The first goal is to clean up the vertical edges with a 1/2" carbide end mill with two...
First time poster. I'm thinking about putting a PRS Standard 96-48-6 in a new garage and I'm wondering about the required work space. I spoke to technical support a while back and I seem to...