Search:

Type: Posts; User: ntraub01

Page 1 of 2 1 2

Search: Search took 0.04 seconds.

  1. Replies
    7
    Views
    6,551

    We opted for the 2" brass ball valves. They were...

    We opted for the 2" brass ball valves. They were a bit stiff at first but they have a large, durable handle on them and are much easier to turn than the PVC valves we've had experience with in the...
  2. Replies
    1
    Views
    5,175

    We have an 8 zone 4x8 vacuum table and the only...

    We have an 8 zone 4x8 vacuum table and the only comment I have about our setup and probably something you should think about is...in a typical cut sheet layout, do you typically group most of your...
  3. Replies
    2
    Views
    1,993

    We are using a USB 2.0 Active Extension Cable of...

    We are using a USB 2.0 Active Extension Cable of 33 feet long, made by Tripp Lite (model: UO26-10M). It is hooked up to a USB 3.0 socket and we've had zero issues with it since installation nearly...
  4. Sorry for the delay, an apparent sinus infection...

    Sorry for the delay, an apparent sinus infection has kicked my butt for the past three days but alas here is the info.

    We are using a USB 2.0 Active Extension Cable of 33 feet long, made by Tripp...
  5. Peter, we have an RBK control box and have...

    Peter, we have an RBK control box and have greatly extended the USB control line from the control box and have also replaced and greatly extended the VFD control cable. Both of these cables were way...
  6. Replies
    15
    Views
    9,726

    Wish I needed another machine!!! Now that...

    Wish I needed another machine!!!

    Now that others have figured out how to easily move these machines, South Dakota isn't tooooo far from anywhere.

    Certainly will be interesting to see what the...
  7. Replies
    4
    Views
    5,480

    Good morning, We are in Spring Hill, KS, just...

    Good morning,

    We are in Spring Hill, KS, just south of Olathe. We could cut your order tomorrow if we have the cut info and can get the material. PM me so we can talk.

    Have a great weekend!!
  8. Replies
    1
    Views
    2,462

    In addition, all vacuum/blower motors need to...

    In addition, all vacuum/blower motors need to have access to free air and we need to run the motors on free air for at least 4-5 minutes BEFORE we shut them down. Our initial install did not include...
  9. Replies
    14
    Views
    8,785

    I "third" the Inland Marine policy! Because it...

    I "third" the Inland Marine policy! Because it is technically "mobile" the Inland Marine policy is the only way it will float. LoL

    HOWEVER, they may balk at it because it is a tool and...
  10. Replies
    18
    Views
    11,276

    The Kent dust shoe is worth every dollar! We...

    The Kent dust shoe is worth every dollar!

    We had sporadic issues with the OEM dust shoe and it usually resulted in a huge panic and material loss as well as some not so great grinding sounds...
  11. Replies
    3
    Views
    3,051

    Project Update...

    Thank you all for lending a helping hand when things weren't working the way "I" thought they should be working!!

    After many months of scratching my head and trying "NOT" to get tooooo many...
  12. Replies
    5
    Views
    3,905

    Thank you all for the advise and I think I'm...

    Thank you all for the advise and I think I'm going to tackle the remaining pieces and parts of this project on Monday.

    The new bits have arrived and I've make some major changes in the remaining...
  13. Replies
    8
    Views
    7,790

    Up until this past month, we nearly ALWAYS used...

    Up until this past month, we nearly ALWAYS used down cut bits as we are always trying to limit the amount of tearout we get on our veneer plywood. I can safely say that 9/10 times we DO NOT use up...
  14. Replies
    5
    Views
    3,905

    A VERY expensive lesson learned!

    After months of design, prototyping and nail biting, yesterday was the day we started the milling process. I had been double checking and triple checking everything before we started and I was...
  15. Replies
    11
    Views
    8,684

    Oops... We are running the 2.2HP spindle.

    Oops...

    We are running the 2.2HP spindle.
  16. Replies
    11
    Views
    8,684

    You guys were right...pat yourselves on your...

    You guys were right...pat yourselves on your backs...

    After reading many of your responses I decided to throw caution to the wind and let the dust fly. I'm now cutting 3/4" MDF with a 1/4"...
  17. Replies
    8
    Views
    9,152

    OH NO YOU DIDN'T... Welcome to the forum. ...

    OH NO YOU DIDN'T...

    Welcome to the forum.

    Just my two cents...90% of my bits are Whitesides, 8% are Amana and I still have all of the Onsrud bits my machine came with minus the one I broke...
  18. Replies
    23
    Views
    15,890

    Beautiful!! I can only imagine the time involved...

    Beautiful!! I can only imagine the time involved with carving such a huge piece. I've got 2.5 hours in a 8x10 piece, though it isn't tweaked for speed either, seriously awesome!
  19. Replies
    9
    Views
    5,707

    Thank you all for the great advice. I would...

    Thank you all for the great advice. I would honestly have even less hair than I currently do if I had not reached out to you all, thank you again!!

    Things are progressing well and I have 2 of the...
  20. Replies
    9
    Views
    5,707

    Needing some carving help!

    Time to dip into the wealth of knowledge to help me with the finer points of 2.5D carving with the SB.

    Software: PW3D
    What: An internment box for my father-in-law
    Material: Cherry
    Size:...
  21. Replies
    44
    Views
    27,574

    Grizzly tools are great machines. We have both...

    Grizzly tools are great machines. We have both Grizzly and Delta table saws and everyone prefers the Grizzly over the Delta. Just because they are not as expensive as the more prominent brand name...
  22. Replies
    2
    Views
    1,741

    Nesting Questions

    Good afternoon all,

    I am about to mill a 45' long serpentine handrail and matching foot rail between which a 38" piece of 3/8" plexiglass will be mounted. Each finished piece of handrail and...
  23. Replies
    26
    Views
    11,164

    This is quite a timely discussion for me, thank...

    This is quite a timely discussion for me, thank you all for your contributions and though I was not the original question poster the information has been great.

    I'm working on approximately 10 -...
  24. Replies
    25
    Views
    10,332

    Just my two dimes... Whatever you can make...

    Just my two dimes...

    Whatever you can make portable or movable do it. We have a large double drum sander and a large planer that take up prime real estate in the middle of our shop because we...
  25. Replies
    4
    Views
    4,727

    Yes, there seems to be a import issue that...

    Yes, there seems to be a import issue that developed when SKP 2015 was released.

    If you back save to 2014 Vectric will import as expected.
Results 1 to 25 of 46
Page 1 of 2 1 2