Search:

Type: Posts; User: gundog

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    11
    Views
    751

    Very sad news. RIP Dave.

    Very sad news. RIP Dave.
  2. Replies
    28
    Views
    2,907

    Thanks Joe that was really helpful.

    Thanks Joe that was really helpful.
  3. Replies
    28
    Views
    2,907

    The design of the sign will not change a lot from...

    The design of the sign will not change a lot from the original I posted but the elements and what the sign says may change it is still going to be a multi layered sign and choosing the proper...
  4. Replies
    28
    Views
    2,907

    Thank you so much for the feedback I just had a...

    Thank you so much for the feedback I just had a conversation with David about some of the things brought up in this thread. He was asking if I knew of any examples of church signs we could look at....
  5. Replies
    28
    Views
    2,907

    Thank you the advice it really helps I would like...

    Thank you the advice it really helps I would like to tweak the design and I have sent a link to this thread to my Pastor David it is not too late to change it until I start cutting. I am leaning...
  6. Replies
    28
    Views
    2,907

    I was hoping to make something like this...

    I was hoping to make something like this http://www.talkshopbot.com/forum/showthread.php?24648-my-first-3d-sign-with-imported-wood-texture&highlight=carved+sign

    What material is this made from? My...
  7. Replies
    28
    Views
    2,907

    Here is the image the software created. I have...

    Here is the image the software created. I have the latest version of Aspire. I have not added any color to anything but the font so it would stand out. I plan to carve the sign and let one of the...
  8. Replies
    28
    Views
    2,907

    It is in bad shape and hand painted over the old...

    It is in bad shape and hand painted over the old church sign (Whipple Creek Church). It is made from 1/4 plastic of some type and painted it has a large corner broken and was designed to be lighted...
  9. Replies
    28
    Views
    2,907

    Hi Joe, I feel the same way my Pastor likes it...

    Hi Joe,
    I feel the same way my Pastor likes it but to me it looks very amateurish I am not very artistic.

    6:8 is a Christian church the 6:8 is from Micah 6:8 "He has shown you O Man what is good...
  10. Replies
    28
    Views
    2,907

    Exterior sign advice.

    I am trying to design and make a new sign for my church. Signs are not something I usually make. Cost is a factor we have a small church and funds are tight. The existing sign is broken but has a...
  11. Thanks for the info guys Bob has offered to sell...

    Thanks for the info guys Bob has offered to sell me a pump I think is going to work very good for this project I will follow up with some pictures and a video using the fixture when I get it built.
  12. These parts are one at a time made in my VMC 50...

    These parts are one at a time made in my VMC 50 part runs. I have been making them on my router table 20 at a time but edge finish is not great and my shop built vacuum system is not really up to the...
  13. Thanks for the info. Bob you can shoot me an...

    Thanks for the info. Bob you can shoot me an email of what you have if you want to. mike@millermarineproducts.com
  14. Planning a vacuum fixture and need help for vacuum source.

    I plan to make a vacuum fixture for this part (see picture)I need a vacuum source either a pump or a venturi type source. Cycle times I expect to be around 5 minutes or less. I will probably make 20...
  15. Try contacting Gary Campbell or Brady on here and...

    Try contacting Gary Campbell or Brady on here and see if they would be willing to come fix it. You will probably save money in the long run paying one of these guys to come to your shop if they are...
  16. Replies
    6
    Views
    973

    I use bits made by Onsrud to machine plastic they...

    I use bits made by Onsrud to machine plastic they are made for soft plastic but you will still see tooling marks if that matters. The 2 flute 52-000 series work best for bottom finish you can also...
  17. Replies
    6
    Views
    954

    I should have mentioned when I did change the...

    I should have mentioned when I did change the router on my Shop Bot I replaced it with a Columbo 3 HP spindle it was a big upgrade. If it were me I would either put in an HSD spindle or try one of...
  18. Replies
    6
    Views
    954

    I used a Milwaukee 3.5 HP for a while on my...

    I used a Milwaukee 3.5 HP for a while on my machine but did not like the collets. I have the big PC on a manual router table and I like it better than the Milwaukee.
  19. Replies
    5
    Views
    949

    Nice work!!

    Nice work!!
  20. Thread: Stepover

    by gundog
    Replies
    13
    Views
    3,683

    Check the drawing and make sure it is a closed...

    Check the drawing and make sure it is a closed vector you can right click on the vector and if you get the choice to close it by moving end points or with a straight line it is open you can also look...
  21. Replies
    9
    Views
    1,092

    Here is a thought you could poor concrete into a...

    Here is a thought you could poor concrete into a form with some leveling bolts in the form the concrete would help stabilize the machine and get you the height you want. Add some steel or rebar in...
  22. Replies
    20
    Views
    2,423

    I have never used flanges on the vacuum tables I...

    I have never used flanges on the vacuum tables I have made I just machine the hole to fit close and seal with silicone. I used the Valtera valves the only thing I don't like about them are the T...
  23. Replies
    11
    Views
    1,754

    My air compressor, Dust collector, Light House...

    My air compressor, Dust collector, Light House vacuum hold down motors and a Vibratory Bowl tumbler all are housed in a loafing shed just outside my shop. I put all the noisy stuff outside it sure...
  24. Replies
    4
    Views
    730

    Make sure not to bottom out the bit in the collet...

    Make sure not to bottom out the bit in the collet before tightening if you do as the collet tightens the threads pull into the collet if the bit is bottomed it will not get tight as it is trying to...
  25. Replies
    10
    Views
    2,273

    Very nice job on the sharpening. I once had a...

    Very nice job on the sharpening. I once had a tool grinder but never had time to learn to use it I eventually traded or sold it I can't remember.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4