Hi Gary,
I brought your last thumb drive showing how to set the link for e cabinet and that was great. I would like to get your new dvd. I know you always do a good job. I will email to you my e-mail
Type: Posts; User: frank134
Hi Gary,
I brought your last thumb drive showing how to set the link for e cabinet and that was great. I would like to get your new dvd. I know you always do a good job. I will email to you my e-mail
I had a w/h also. Great machine. I did good by me. Trick is to take a last cut very small.
That a very nice setup. Gary really know his stuff. But I was wondering what did it cost if I may ask?
Hi Gary. What is the cost for the extra and what all do I get?
Just wanted to say thank Scott. You were right on. I guess I was so worry about doing the doors I did think.
Again thank
Frank
I need some help. I am making some big white oak doors 1.5 x 39 x 96”. The specs call for all tenons and mortise joints. The tenons being .75" thick by 3” wide by 3" deep with mortise to match. I...
i need to cut some mortise that are 3" deep. The only end mill I can
find are 5/8" x 4.50". Do you think it will be all right. I got a 4hp
spindle and also order 5/8" collet .
I have one. I used it for auto cadd and an est software pro I have. I don't use it any more. It just collect dust in the corner. Yes it worth around 1500. if you need a tracing board. The does...
Hi. I just wanted to say thank shopbot for the great camp and for the really good food they had for all of us. Me and my son learn a few good thing and we really enjoy our self. Just can't wait till...
Thank Jack,
I try that. It did not help. I just keep stopping in the same place. Something it will run the whole program and other time it won't. It got me.
here is a screenshot of the error
For some reason I am getting a driver/motor fault! Location ??-- . Just about the same location in the x axis at about 72 ". Doesn't care on the y axis just the x and it doesn't happen all the time....
I had a problem like this a awhile. It took me some time to figure it. It was the bit I was using. The company I got it from put a hard coat of metal on the end of the bit to extend it life. Sometime...
Hi,
All I can say here is you all better read up on prevailing wage. There are six kind first. residential, commercial and highway and these can be federal or state. All of these can be different...
plastic air line are not an osha violation. We have wire a lot of commercial shop and seem them use plastic pipe. as for schedule 40 pipe their are high pressure fitting for it that you can used. The...
This is what I did. you can't see them, but I but number by the bit and make a spread sheet with the info for that number. type, price and where I bought them.
I am also interested
Pat I used the 66-300 and the bottom came out nice and clean. I could hardly beleive it . It almost look like a mirror finish. I cut in the material about 1/2" in 1/8" step.
you know they did not make you up date. Like me I took the update. so I kill two cheap sheet of ply to practice on. After three day I was ready to trun back. Then I found the error. they were mine. I...
make sure you stir and don,t shake the mix. stir slow.
Now tell me who build it you or did your son help?
Yes I ment the one you could add button too. I can't seam to get it to work at all.
What happen to the tool bar. I can not seem to get it to work. Is their something I need to read?
That not bad but $800.00 for just a trace software is a little to much.
john sent me and e-mail. $800.00 for the software. That a little to much just to trace a part on a board. I have a 5 x 4 gtco digitizing tablet ( that was over 2000.) that we use for construction...