Search:

Type: Posts; User: cowboy1296

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    24
    Views
    2,245

    its 19.4 inches round with the officers name not...

    its 19.4 inches round with the officers name not showing
  2. Replies
    24
    Views
    2,245

    I really like the racoon. with what is going...

    I really like the racoon. with what is going on In the world today I hope that everyone stays safe and healthy. I have not posted anything in a while so I hope that you...
  3. yup that is exactly how i do it. And if the...

    yup that is exactly how i do it. And if the differance in the preview is not so great go with the larger bit, if it is great go with the smaller bit.
  4. Scott will forget more about 3-d then i will ever...

    Scott will forget more about 3-d then i will ever learn. That said I am curious about the size of your model. Do you know how to determine which size ball nose to use? It would not hurt to...
  5. Replies
    20
    Views
    2,225

    My fairly new shop is barn shaped 16x20x16. I...

    My fairly new shop is barn shaped 16x20x16. I left the floor concrete. i have a wall mounted 30 amp heater which does a great of warming it up. Now am i messing up by leaving the floor concrete?
  6. Replies
    4
    Views
    352

    running no but in a shop yes. I have asked one...

    running no but in a shop yes. I have asked one of the administrators to remove this post and then I will put up another to see if there is anyone in Colorado who is interested. The longest was...
  7. Replies
    4
    Views
    352

    don't know yet but I may not do anything or I ...

    don't know yet but I may not do anything or I might keep both. but I seem to remember similar comments in the past. but I am old and may be confusing this site with another. but if the...
  8. Replies
    4
    Views
    352

    No comment yet just thinking

    Just something that I am only pondering, no commitment of any kind yet. But I am thinking of selling my buddy with a 4 ft power stick and upgrading to a Legacy Maverick 3x5. Just curious, anyone...
  9. Replies
    6
    Views
    652

    they are most noticeable when doing 3-d, but v...

    they are most noticeable when doing 3-d, but v carving could be better. I cut perfect circles but at times there appears to be some chatter in the v grooves.
  10. Replies
    6
    Views
    652

    I have a buddy prs. I rocked along for years...

    I have a buddy prs. I rocked along for years without changing my pinions. I finally did for no other reason than the fact that they were like me, old. That is when my problem began and has not...
  11. Replies
    6
    Views
    652

    Newest control software

    I have not been happy for a very long time with the quality of cuts that i have been getting on my 3-d carvings. It appears that it is a z-backlash. But most of the time i can sand out the uneven...
  12. Replies
    18
    Views
    1,384

    Just one word "wow"

    Just one word "wow"
  13. Thread: Work shop

    by cowboy1296
    Replies
    8
    Views
    1,212

    Its tuffsheds design but i upgraded it a lot. ...

    Its tuffsheds design but i upgraded it a lot. due to my traveling electricity wont go in until the 18th of september then blow insullation. once electric is in i can tell you all about it.
  14. Thread: Work shop

    by cowboy1296
    Replies
    8
    Views
    1,212

    16x20x16. you never heard anyone say i built my...

    16x20x16. you never heard anyone say i built my garage, shed or work shop to big. but this should do it.
  15. Thread: Work shop

    by cowboy1296
    Replies
    8
    Views
    1,212

    yeah i hear ya but no shes here except the deer....

    yeah i hear ya but no shes here except the deer. i figure about a week i can shovel all the sawdust out of the bed of my pick up.
  16. Thread: Work shop

    by cowboy1296
    Replies
    8
    Views
    1,212

    Work shop

    I have been working out of the corner of my garage since the beginning of my http://www.talkshopbot.com/forum/attachment.php?attachmentid=33187&stc=1shopbot. Even my truck is sawdust brown in color....
  17. Replies
    23
    Views
    3,607

    Brady, i will check the x mount but can not find...

    Brady, i will check the x mount but can not find any input on the power stick handle. After slowing my speed down and cutting across the grain and in a raster cut, i am not so upset with the...
  18. Replies
    23
    Views
    3,607

    scott, actually my buddy is running as good as...

    scott, actually my buddy is running as good as the one in the video, maybe some slop in the x still working on that. whenever i did offset i was moving way to and when it got to the top of the bowl,...
  19. Replies
    23
    Views
    3,607

    i dont even know how to spell hdu but thanks for...

    i dont even know how to spell hdu but thanks for the idea. when i went from offset to raster and slowed my speed down it seemed to help a lot. i have taken 2-3 readings with the dial indicator and...
  20. Replies
    23
    Views
    3,607

    it may be me being too anal and i am guilty of...

    it may be me being too anal and i am guilty of being that. a...
  21. Replies
    23
    Views
    3,607

    unless i am doing something wrong my brand new ...

    unless i am doing something wrong my brand new dial indicator is telling me that i have .013 of movement on the x which seems like more than just a tick, i am also putting a lot of pressure on the...
  22. Replies
    23
    Views
    3,607

    i dont want to say who told me to run at ultra...

    i dont want to say who told me to run at ultra high speeds, but it came from two who should be in the know. i still think that i have an abused x stepper motor and bought my first dial indicator this...
  23. Replies
    23
    Views
    3,607

    if you sent me a pm i am not seeing it, you can...

    if you sent me a pm i am not seeing it, you can email me at ashwood1296@gmail.com if you like
  24. Replies
    23
    Views
    3,607

    Thanks for the comments and i will keep those...

    Thanks for the comments and i will keep those used motors in mind.
  25. Replies
    23
    Views
    3,607

    thanks, that gives me a lot to think about

    thanks, that gives me a lot to think about
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4