Search:

Type: Posts; User: Simops

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    13
    Views
    1,440

    The board cost (after applying the Aussie peso...

    The board cost (after applying the Aussie peso exchange rate and international priority mail) just over $350
    But I can’t complain as I purchased the Buddy PRS 48 in 2011 and this has been my first...
  2. Replies
    13
    Views
    1,440

    Just a final follow up in case any one else in...

    Just a final follow up in case any one else in this situation. The controller board (the one that the USB cable is connected to) was indeed fried. Shopbot sent out a new one and once installed...
  3. Replies
    13
    Views
    1,440

    Hey Guys.....I’ve got Shopbot techs on the case...

    Hey Guys.....I’ve got Shopbot techs on the case now. It’s narrowing down to the USB control card .....it looks like it might have given up the ghost!!!!......just waiting for confirmation......
  4. Replies
    13
    Views
    1,440

    Jut had a look and the LEDs on the main board and...

    Jut had a look and the LEDs on the main board and the piggy back board that the USB lead is connected to are on.....not blinking though.
    The fuses are good. I don’t have a 12v supply that I can...
  5. Replies
    13
    Views
    1,440

    Thanks guys......I’ll check the power...

    Thanks guys......I’ll check the power supplies.....looks something has failed so will be contacting SB
    The controller does have a small board piggy backed onto the main control board.....I’ll check...
  6. Replies
    13
    Views
    1,440

    Shopbot Controller

    Guys,

    Before I contact Shopbot on Monday (10000 miles away:) )I'm hoping someone here has had this issue and can help.

    Turned on PRS Buddy 48 and shopbot control software spits the dummy and...
  7. Replies
    6
    Views
    950

    Wow that’s amazing!! Here you can’t buy a...

    Wow that’s amazing!! Here you can’t buy a handgun unless in a gun club or security organisation. And long arms only by farmers and hunters but only after going through a rigorous background...
  8. Replies
    8
    Views
    1,649

    Yep that's why he has two of them...... Nice but...

    Yep that's why he has two of them......
    Nice but I have narrow spaces in places that would not allow it to fit through so no good for me at this time!!
    Cheers
  9. Thread: z axis upgrade

    by Simops
    Replies
    4
    Views
    1,325

    Yep I'm with Andrew....I only lifted mine by inch...

    Yep I'm with Andrew....I only lifted mine by inch and a half and that was enough for my needs.....no more banging the spindle at top travel limit. I guess if I was going to use a rotary indexer...
  10. Not sure if I'm understanding this but the way I...

    Not sure if I'm understanding this but the way I do it is in vectric (in my case Aspire) material setup section I select zero to spoilboard, set the material depth as per usual and that's it. Use...
  11. Replies
    12
    Views
    2,337

    Has anyone actually used one yet? Interested to...

    Has anyone actually used one yet? Interested to see how accurate it really is......90 deg / 45 deg......are they accurate?
  12. Thread: Power Stick

    by Simops
    Replies
    1
    Views
    792

    It's best to email Shopbot on this to get 100%...

    It's best to email Shopbot on this to get 100% confirmation.
  13. Same but I'll wait for the video when it gets...

    Same but I'll wait for the video when it gets released as I'm other side of the world!
  14. Replies
    6
    Views
    1,556

    Are these similar to the Raptor nylon nails....I...

    Are these similar to the Raptor nylon nails....I have used these for nailing down the spoilboard before I went to vacuum.
    I just used a cheap off-the-shelf finish gun which worked fine for the...
  15. Replies
    11
    Views
    3,247

    Ditto! Fantastic effort...... I hope all goes...

    Ditto!
    Fantastic effort......

    I hope all goes well with your son's treatment.........

    Cheers
  16. Replies
    5
    Views
    2,180

    Yep I would pay.......if it was in...

    Yep I would pay.......if it was in Australia...:rolleyes:.
  17. Thread: Sales this Year

    by Simops
    Replies
    7
    Views
    1,854

    Well done Eugene.....they are good bulk orders to...

    Well done Eugene.....they are good bulk orders to start the year off!
  18. Replies
    5
    Views
    2,056

    As Kyle says.....more info needed.... If the...

    As Kyle says.....more info needed....

    If the object is smaller than your table area consider masking off the rest with non porous, smooth material.....I use plexiglass, aluminium, etc.

    Also my...
  19. Replies
    21
    Views
    6,130

    Andrew, my Buddy is approaching the same...

    Andrew, my Buddy is approaching the same age......was wandering, other than some slight inaccuracy that you noticed is there anything else that made you think that you definitely needed to replace...
  20. Replies
    9
    Views
    2,707

    Not sure if this helps but I had a reason to...

    Not sure if this helps but I had a reason to change my X & Y 0,0 co-ordinates and also reverse my X and Y axis......why because with my Buddy I wanted to stand on the left and have the X go left to...
  21. Replies
    14
    Views
    5,408

    I purchased from the Golden Bridge Precision...

    I purchased from the Golden Bridge Precision Machinery Co Ltd. The air filter pictured (black canister) is 34USD per piece when I bought it a couple years ago.
    email contact is Kate:...
  22. Replies
    14
    Views
    5,408

    Standby.....I'll find the contact email for you...

    Standby.....I'll find the contact email for you tomorrow ....it's on my work computer .......
  23. Replies
    14
    Views
    5,408

    This my canister filter.....similar to the pic...

    This my canister filter.....similar to the pic you show.....
    Purchased it from same Chinese place I got my pump
    29221
  24. Replies
    38
    Views
    10,460

    Walnut.....love it but I can only get as 8...

    Walnut.....love it but I can only get as 8 quarter as an import here because so expensive......you are lucky in North America to have that wood so readily available in those sizes. Nice to work...
  25. Replies
    8
    Views
    1,987

    For a Buddy or table?

    For a Buddy or table?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4