Search:

User: brian_h

Search: Search took 0.03 seconds.

  1. A simple question: Colombo replacement collet nuts

    Started by brian_h, 08-12-2009 01:16 PM
    1 Attachment(s)
    • Replies: 6
    • Views: 4,284
    Last Post: 08-14-2009 09:16 AM
    by cabnet636  Go to last post

    Forum:
    ShopBotter Message Board

  2. Can't get the drivers to reset after digging into a board.

    Started by brian_h, 09-22-2007 02:20 PM
    • Replies: 2
    • Views: 2,211
    Last Post: 09-22-2007 03:21 PM
    by brian_h  Go to last post

    Forum:
    Archives2007

  3. Who needs Trupan in Minneapolis?

    Started by brian_h, 09-17-2007 12:07 PM
    • Replies: 5
    • Views: 2,535
    Last Post: 09-18-2007 09:59 AM
    by andre  Go to last post

    Forum:
    Archives2007

  4. Who has a hybrid, vacuum/t-slot table?

    Started by brian_h, 09-16-2007 10:17 PM
    • Replies: 2
    • Views: 2,435
    Last Post: 09-16-2007 11:00 PM
    by Gary Campbell  Go to last post

    Forum:
    Archives2007

  5. Is baltic birch a *good* choice for a plenum board?

    Started by brian_h, 09-16-2007 10:30 PM
    • Replies: 1
    • Views: 1,637
    Last Post: 09-16-2007 10:55 PM
    by Gary Campbell  Go to last post

    Forum:
    Archives2007

  6. Grey HDPE at Menards- any good uses???

    Started by brian_h, 03-13-2007 11:44 PM
    • Replies: 5
    • Views: 4,172
    Last Post: 03-15-2007 11:07 AM
    by jhicks  Go to last post

    Forum:
    Archives2007

  7. Drilling holes w/ either VCarve or PW

    Started by brian_h, 02-07-2007 10:00 PM
    • Replies: 3
    • Views: 2,695
    Last Post: 02-08-2007 01:11 PM
    by Brady Watson  Go to last post

    Forum:
    VCarvePro and PhotoVCarve

  8. Is that Brady's voice...

    Started by brian_h, 12-16-2006 01:05 AM
    • Replies: 2
    • Views: 1,847
    Last Post: 12-16-2006 11:20 AM
    by brian_h  Go to last post

    Forum:
    Archives2006

  9. Cost of a 4x8 sheet of SignFoam????

    Started by brian_h, 09-22-2006 01:34 PM
    2 Pages •
    1 2
    • Replies: 15
    • Views: 21,716
    Last Post: 10-30-2006 07:07 PM
    by tuck  Go to last post

    Forum:
    Archives2006

  10. About cutting inlay for guitars...

    Started by brian_h, 10-06-2006 07:13 PM
    • Replies: 5
    • Views: 2,544
    Last Post: 10-11-2006 01:14 PM
    by sagreen83  Go to last post

    Forum:
    Archives2006

  11. Leveling Bit...

    Started by brian_h, 09-14-2006 02:18 PM
    3 Pages •
    1 2 3
    3 Attachment(s)
    • Replies: 24
    • Views: 6,085
    Last Post: 09-21-2006 09:05 PM
    by brian_h  Go to last post

    Forum:
    Archives2006

  12. Time to select bits for 3D cutting.

    Started by brian_h, 09-13-2006 03:01 PM
    2 Pages •
    1 2
    1 Attachment(s)
    • Replies: 15
    • Views: 4,676
    Last Post: 09-15-2006 07:38 PM
    by patricktoomey  Go to last post

    Forum:
    Archives2006

  13. Zero plate clamp closes circuit anytime it touches the bit (or machine).

    Started by brian_h, 09-04-2006 07:58 PM
    1 Attachment(s)
    • Replies: 3
    • Views: 2,524
    Last Post: 09-04-2006 10:38 PM
    by brian_h  Go to last post

    Forum:
    Archives2006

  14. Easiest Question Ever

    Started by brian_h, 08-07-2006 11:03 AM
    • Replies: 8
    • Views: 3,118
    Last Post: 08-07-2006 07:07 PM
    by bleeth  Go to last post

    Forum:
    Archives2006

  15. Missing "readme" file for EULA on USB to Serial Adapter disk.

    Started by brian_h, 08-06-2006 01:40 PM
    • Replies: 5
    • Views: 2,171
    Last Post: 08-06-2006 07:04 PM
    by brian_h  Go to last post

    Forum:
    Archives2006

  16. Protecting VFD from dust.

    Started by brian_h, 08-04-2006 07:35 PM
    • Replies: 1
    • Views: 1,680
    Last Post: 08-04-2006 07:44 PM
    by richards  Go to last post

    Forum:
    Archives2006

Results 1 to 16 of 16