Search:

Type: Posts; User: Red F

Page 1 of 5 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    1,066

    I just looked up your website and that is some...

    I just looked up your website and that is some AMAZING work!
  2. Replies
    3
    Views
    846

    I had a Buddy so I can't say exactly, but I think...

    I had a Buddy so I can't say exactly, but I think it is the length of cut plus the width of the gantry. With the ATC, are the tool holders along the side or off the end? If they are off the end,...
  3. Replies
    7
    Views
    3,019

    I've dabbled with a Ender3 pro from Creality and...

    I've dabbled with a Ender3 pro from Creality and found it to be a great value. Your Prusa probably has a better print quality, but I'm making stuff for around the house, around the shop, and models...
  4. Replies
    5
    Views
    897

    I agree with the Scotts.

    I agree with the Scotts.
  5. Replies
    1
    Views
    699

    Have you checked your part file to see if it is...

    Have you checked your part file to see if it is giving a different z height for the 2 processes? I run non-blue router and I was having a problem with the first pass not going deep enough. Looking...
  6. Replies
    2
    Views
    1,037

    Only thing that springs to mind, is I get alot of...

    Only thing that springs to mind, is I get alot of leakage around the perimeter of my spoilboard, and if it hasn't been surfaced in a while I see a drop in pressure.

    Also when we are running...
  7. 4x8 PRS Alpha with Vacuum for sale in New York

    Not my machine and don't know anything about it, but it looks like a great deal.

    https://www.woodweb.com/exchanges/machinery/posts/531871.html
  8. Replies
    13
    Views
    2,819

    Thanks for the update. Glad you got it sorted out

    Thanks for the update. Glad you got it sorted out
  9. Replies
    13
    Views
    2,819

    Have you tried running the program while doing an...

    Have you tried running the program while doing an air cut and is it the same result?
    I wonder if it is a static/grounding issue?
  10. Thread: Z-Depth Trouble

    by Red F
    Replies
    21
    Views
    4,469

    My bet is that when you are flattening your...

    My bet is that when you are flattening your table, the vacuum does not have as much downforce on the open table as it does when it is covered with masonite. So the middle section is sitting higher...
  11. Replies
    2
    Views
    2,299

    Not sure if it helps, but this is my tidbit of...

    Not sure if it helps, but this is my tidbit of knowledge on a similar topic.

    We have an older 16bit software system at work, and one problem I have had is the 64 bit computers will not run it. ...
  12. Thread: Forum Jibberish

    by Red F
    Replies
    4
    Views
    2,121

    I believe that is where the computer doesn't...

    I believe that is where the computer doesn't recognize quotation marks or something like that. Like this "
  13. Replies
    8
    Views
    1,943

    DWG is autocad. If there is a drafting teacher...

    DWG is autocad. If there is a drafting teacher at your high school, they may have software that could open it. Otherwise see if he has it saved as a DXF. Aspire can import those.
  14. Replies
    1
    Views
    1,804

    More CFM is more better.

    More CFM is more better.
  15. Thread: Hole not round

    by Red F
    Replies
    7
    Views
    3,602

    I found when I was running my router with a climb...

    I found when I was running my router with a climb cut on small holes at high feed rate, my holes looked like yours. I had a little slop in the machine like bill.young just talked about and the climb...
  16. Replies
    12
    Views
    6,982

    I'm sorry that I am no help answering your...

    I'm sorry that I am no help answering your question, but I am curious about your vacuum setup. I'm trying to work out some vacuum workholding form my machine and I wonder, are each of your pods...
  17. Replies
    5
    Views
    6,346

    Just from what I remember looking at the one I...

    Just from what I remember looking at the one I used to own. I believe that if you run your table too far back, it bumps into that bolt and kicks the stepper motor out a tiny bit so that it doesn't...
  18. Replies
    11
    Views
    4,387

    Thank you for the clarification Eric. I...

    Thank you for the clarification Eric. I appreciate it.
  19. Replies
    11
    Views
    4,387

    Thank you Eric for the recording of the Webinar. ...

    Thank you Eric for the recording of the Webinar.

    I played with the calculator a little bit and one thing I am a little confused on is the relationship between depth of cut and chipload. It is...
  20. Thread: Table legs

    by Red F
    Replies
    13
    Views
    6,309

    Reminds me of this old thread. ...

    Reminds me of this old thread. http://www.talkshopbot.com/forum/showthread.php?24604-White-oak-table

    He was building 4 sides for each leg and mitering them together
  21. Replies
    4
    Views
    2,961

    One possibility is that your bit isn't truly 120...

    One possibility is that your bit isn't truly 120 degrees or 90 degrees. That would cause over-cutting in the corners like you see on the body of the "I". You can test out cutting some sample...
  22. Thread: 4x8 prt standard

    by Red F
    Replies
    12
    Views
    12,050

    I'm guessing it is in Cookeville TN

    I'm guessing it is in Cookeville TN
  23. Thread: Is CNC cheating?

    by Red F
    Replies
    25
    Views
    24,512

    I know I'm kind of a smart ass, but I named my...

    I know I'm kind of a smart ass, but I named my router "Hand". Got around that "hand made" problem.
  24. Replies
    9
    Views
    9,045

    Eric, that model is great and I'm digging that...

    Eric, that model is great and I'm digging that table you have the model on. We are setting up a new to us non-blue CNC at work and I need to build an off-load table for it. I think I'll try to do...
  25. Replies
    14
    Views
    21,507

    It looks like the tool path is not set for a 60...

    It looks like the tool path is not set for a 60 degree bit, or your z is not zeroed correctly.
Results 1 to 25 of 108
Page 1 of 5 1 2 3 4