Cody,
Send us an email at support@shopbottools.com with the cut file you are running and we can help.
Best Regards,
Tom
Technical Support
ShopBot Tools, Inc
Type: Posts; User: tomhartnett
Cody,
Send us an email at support@shopbottools.com with the cut file you are running and we can help.
Best Regards,
Tom
Technical Support
ShopBot Tools, Inc
Here is a writeup that was done by one of our engineers at ShopBot on the differences between different vacuums as well as some info on how to think about them and their efficiencies, this may help....
Speeds and feeds are not set in stone and many have different approaches to dialing them in. This is where you get varying starting RPMs and feed rates when you look at different charts. They are...
I've closed this thread as we'd prefer to keep the discussion on here limited to CNC and such. I will leave it up for now as I don't like deleting/censorship.
The development of FabMo was delayed primarily by the discontinuation of the Intel Edison, FabMo was ready for release when the Edison was scrapped by Intel. This set development of the controller...
The Desktops are being sold with SB3 (old card) currently. It is the tool that FabMo will first be released on however and retrofitting an older DT with FabMo should also be a straightforward...
It is not often that I am able to check in to this forum. I was alerted to this thread earlier and wanted to clear up some misinformation.
As I've mentioned on this forum before, the "Comm error"...
I have not offered any more insight into this thread because I don't feel I have anything new to add that has not already been stated earlier in this thread ("Mr. Sturmer" actually has partaken and...
Hi Judson, the ShopBot partner promotion we provide can be used by any ShopBot user. Installing the software on all the lab computers is not a problem, I believe where you will run into a hangup is...
Pictures can help get you more visibility too, John!
Yeah the sides weren't too complicated at the time, just no longer have them here at ShopBot :)
-Tom
Just to clarify some info for prospects. 2004 would be a 96x48 PRT Alpha (PRS started in 2007) - which include a small difference in the controls, it would likely be run on a serial-usb connection...
For sure, the zero plate is all based off the trigger of input 1 which is controlled by this on/off switch that exists between the clip and the plate. For some bits, this conductive trigger does not...
Thanks for sharing the method! I've not seen this product.
Strange, the aluminum ZZero plate method we use is quite consistent nowadays (and for some time now). It is simply an open/close circuit...
Good to hear it is working again for you, Gene.
When you physically crash the alpha step motors (run it up against a physical stop) the closed loop steppers fault and let the control system know...
Hi Vinny, we just need to know the model of spindle and VFD to get you going. Feel free to write in to support@shopbottools.com anytime for direct support, but basically all spindles are actually run...
Some new videos have been published to our YouTube channel today that cover just about everything one needs to know to setup the control computer for the ShopBot.
It's objective is to be clear...
The beginning of August 2017 is when the Desktop received the design update with two Y axis drive motors and frame improvements
Some of the differences can be seen in the pictures in each Quick...
The issue here was that the DIP switch on the main control board was set to ROUTER instead of SPINDLE. causing the VFD to not power until the start button was pressed (engaging the contactor)
-Tom...
We in support are also happy to get the V4G control board running or help find what the issue was if you ever installed it again or tried to get it working even though it is second hand. Just shoot a...
When the bit touches the plate, does input 1 trigger in the software?
With regular motion commands does the z move both up and down correctly? I'd give it Move->Z, 1 and Move->Z, 0 commands.
Do...
Do you think that it started happening 4 years ago when you first got it?
I would first suspect that the resistors for the drivers may be the incorrect specification for your motor amperage,...
Stay safe!
Checking right at the input terminals or sometimes the output of the contactor is the best way to tell if you should be getting juice
-Tom
These are mostly the 3.6v3.8 differences:
http://www.shopbottools.com/mSupport/SBCSversion38features.htm
however, I never recommend that soemone change versions if they are currently working. if...
Here is a doc and video we normally provide for cutting aluminum (the alloy is really important though :( some are really bad/hard to machine)
31453
https://www.youtube.com/watch?v=glfoB7THcqs...
That is me lol, I generally am not in the support email/calls as my time is stretched nowadays working on video documentation, but I do hop in occasionally and noticed your email :)
Contacting...