Here are some additional photo, to help provide a bit more info
Type: Posts; User: Captive
Here are some additional photo, to help provide a bit more info
Its not crated to ship I just have it in the corner and built a shelf over top of if but could create it that would not be a problem.
I am very open to a reasonable offer if you like you can email...
Hello, Don
Just le me know if you have any questions
Regenerative Blower ( 10 Hp , 220V Single Phase, 215 CFM )
This unit has only about 60 hours of running time on it.
Shortly after purchasing my PRS Alpha Shopbot in 2016 I move from one shop...
PRS Air Drill Head Double Valve R2
This unit has only about 10 hours of running time on it.
Shortly after purchasing my PRS Alpha Shopbot in 2016 I move from one shop to another and did not...
Sorry should have mentioned 1 1/4 Diameter bit. Machine is a new model PRS Alpaha with a 2.2 Hp spindle.
If cutting hard wood ( maple & walnut).. more specifically V-Carving what you be your max depth of cut in a single pass for a 120 Deg V bit you would do... and around what feed / speed & RPM would...
Thanks your for the advice, it is much a appreciated, I will increase the feed speed on the next one... but just a quick question with regards to material burning when V-Carving is a matter of just...
I was cutting out a round maple plaque and when cutting out the perimeter I got some real bad tear out on the edge... not sure why.
Material thickness 0.85
Cut with Straight cutter
3 passes
Rpm...
Okay... thanks... :).... looks like I will just be setting up a second computer next to the shopbot...
I would like to use my computer to draw in Vcarve at the same time the shopbot is running a program off the computer. I know that this is not recommended but I am wondering if it can be done… thanks
No,... it felt fine.. I real can't say if before I adjusted the bearings they were to tight or loose, I just loossened them all and then snugged them back up...hope this helps
regreever
I did not take the spindle off... . There is a document on the shopbot web site...http://www.shopbottools.com/ShopBotDocs/gantry.htm the document name is "adjusting Z car bearings". Just...
!!!!!!! SOLVED !!!!!!!
Well after a fair bit of trouble shooting and bit of frustration I believe I got it figured out.
I needed to adjust the " Z" axis Bearings as per the document on the...
Yes, Top or the material
Machine is a PRS Alpha Gantry 48x 96
Burkhardt
I re-read your post again.... I will try cut this out with and endmill tomarrow...and if I can post a video...if not photos..But when I was watching it closely it causes that odd divot...
The machine I have is a PRS Alpha... only a few months old, and less then 150 hours of cut time on it. I checked the V-rollers bearings on the Y-Car and they are tight... no play that I could feel....
So I made some more test cuts today with a 120 Deg bit and 90 Deg bit using sharp internal corners and cut just a basic letter “ C” shape and I attached in the pictures are the results…. Its...
Burkhardt,
Iam cutting this with a profile & fluting tool path and it happens during the fluting tool path, thats when it happens...am I understanding what you are asking correctly ?
Scottp55,...
Brady,
I have look at the simulation a few times and it does not show the divots... and I just checked this again and no divots..
I think I might try re-draw this from the start just in case I...
I should also add I learned another very import lesson... double check your numbers when changing VA values.... attached is a pic... I meant to change Z to 1.05 but i think i changed it to 10.5.......
RossMosh
I am not sure I know what you mean...can you explain a bit more...thanks
Just want to say thanks for everyone for there help with this….I got a chance to work on this again today and still getting the same results….here is what I did.
1) Used a few more clamps to hold...
Coryatjohn,
I attached a 2 pictures of the preview… I check this and it does not do anything odd, in fact the edges look clean and crisp.
Pau_Z
I drew this using straight line vectors and the...