Search:

Type: Posts; User: Brady Watson

Page 1 of 20 1 2 3 4

Search: Search took 38.62 seconds; generated 1 minute(s) ago.

  1. Watch out for nails... Gene.... Palumbo was...

    Watch out for nails...

    Gene.... Palumbo was trying to link up with you
  2. The physical 0,0 typically being, the corner of...

    The physical 0,0 typically being, the corner of the spoilboard. A vbit works nicely as an indicator to reference the center of the bit

    Now that I am thinking about it...make sure the limit for...
  3. You don't need to manually pull the axes on...

    You don't need to manually pull the axes on startup. This is more for gantry tools than BT series tools.

    In some cases, if the switch proves to be good (from your test with screwdriver they sound...
  4. Replies
    2
    Views
    208

    It depends on how much you want to spend...there...

    It depends on how much you want to spend...there are several options:

    1) Shopbot sells a RetroZ with PRS style rails
    2) Source your own steel and make another
    3) File the edges true again and...
  5. Replies
    12
    Views
    579

    Unfortunately ALL of the SB gearbox motors wear...

    Unfortunately ALL of the SB gearbox motors wear out over time - especially when they are either under heavy load or long repetitious cycles. Early on I built a scanning machine based on a SB that...
  6. Replies
    31
    Views
    2,219

    THIS PLACE HAS BECOME ONE BIG ADVERTISEMENT FOR...

    THIS PLACE HAS BECOME ONE BIG ADVERTISEMENT FOR BRADY WATSON

    There it is folks. The ultimate truth. You got me.
  7. Replies
    5
    Views
    610

    Just make your own power stick...It ain't rocket...

    Just make your own power stick...It ain't rocket science. You need a longer rack, 2 rails and something to tie it all together.
  8. Replies
    5
    Views
    361

    Cue the grown men clutching their pearls...

    Cue the grown men clutching their pearls...
  9. Replies
    6
    Views
    299

    Very nice. I like the less is more on the tail...

    Very nice. I like the less is more on the tail section of the dragonfly.
  10. What do you want...a lathe or indexer?...

    What do you want...a lathe or indexer? Unfortunately you have to pick a lane as they are mutually exclusive.

    You can use a lathe bed and head/tail and add a stepper, driver and cable or buy any of...
  11. Replies
    31
    Views
    2,219

    There are a number of reasons...some of which...

    There are a number of reasons...some of which have been already mentioned.

    The givers got tired of the takers taking & expecting 'handouts'...so with no reciprocity to fill their cups as cohorts,...
  12. Replies
    15
    Views
    884

    That's comedy right there...;)

    That's comedy right there...;)
  13. Replies
    15
    Views
    884

    Glad you got it. Good thing SB makes every wire...

    Glad you got it. Good thing SB makes every wire blue...but at least they label them...
  14. Replies
    10
    Views
    538

    Good job Chuck. The beauty of steel is that if...

    Good job Chuck. The beauty of steel is that if you mess up or need to change something, it's a matter of getting out the wheel, hacking off the afflicted and welding it back up. Besides steel is much...
  15. Replies
    15
    Views
    884

    If the 4G was upgraded from a 3G board, or...

    If the 4G was upgraded from a 3G board, or ordered without a spindle there won't be a 24v ps in the box. You just add one.
  16. Replies
    15
    Views
    884

    The 24v ps in the control box (HSD spindles) -...

    The 24v ps in the control box (HSD spindles) - Colombo spindles are powered thru the VFD. 230v spindles have 230v fans...460v spindles have 24v fans, also powered thru the VFD.
  17. Replies
    15
    Views
    884

    Correct. The motor drivers in the control box....

    Correct. The motor drivers in the control box. When energized AND a motor is hooked up to it, it will light up green. No motor, it will flash red. If you attempt to move a motor with a broken wire,...
  18. Replies
    15
    Views
    884

    Check all wiring - with the control box OFF. Make...

    Check all wiring - with the control box OFF. Make sure nothing got yanked. You may need to carefully cut back the shrink on the motor connectors to make absolutely sure they didn't get yanked and...
  19. Replies
    51
    Views
    6,247

    Yearly maintenance is around $1500. For those...

    Yearly maintenance is around $1500. For those with sticker shock, CarveCo is about the same price as ArtCAM was 20 years ago give or take $150. Maintenance fees are also about the same. I'm really...
  20. Replies
    2
    Views
    347

    Kip, Send me a sample file via email. Zip it up...

    Kip,
    Send me a sample file via email. Zip it up first. I should be able to convert it for you. It's easiest to email from my website.
  21. Replies
    5
    Views
    597

    Best yet Russ :cool:

    Best yet Russ :cool:
  22. Replies
    4
    Views
    1,465

    Please try the following: 1) Run VR command....

    Please try the following:

    1) Run VR command. At bottom of fill-in sheet, click on Reset.

    2) Slow things down to 2,1 and see if it still loses steps/position.

    What machine are you running?...
  23. Replies
    3
    Views
    342

    Email sent....

    Email sent....
  24. What? $25!!! It should be free! Those 3D reliefs...

    What? $25!!! It should be free! Those 3D reliefs just come into existence on their own...anyway, right? :p
  25. Replies
    15
    Views
    1,160

    Get yourself a thread gauge too if you don't...

    Get yourself a thread gauge too if you don't already have one in your tap and die kit. Don't expect most big box stores to have taps in stock... that would be too useful...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4