Search:

Type: Posts; User: paul_z

Page 1 of 18 1 2 3 4

Search: Search took 0.56 seconds; generated 14 minute(s) ago.

  1. Replies
    35
    Views
    54,951

    "I do have excess motor cable looped under the...

    "I do have excess motor cable looped under the table" If it is all coiled in one direction, it forms an inductor (coil). It would only be a micro henry or so but still a coil. if you take half of...
  2. Can you run a humidifier in your shop? Perhaps...

    Can you run a humidifier in your shop? Perhaps put water in a spray gun?

    Paul Z
  3. Replies
    20
    Views
    20,697

    This is a bit off subject but might surprise a...

    This is a bit off subject but might surprise a lot of people. Carbide bits are not solid carbide. If they were, they'd be extremely expensive and brittle to the point of being useless.
    ...
  4. Replies
    7
    Views
    7,046

    pro70z28...

    pro70z28

    If you use an airgun to blast air around the switch/speed control, you may find the switch is bound up with saw dust. If so, it's a trivial fix.

    Paul Z ...
  5. Replies
    2
    Views
    2,414

    That's what my PRT Alpha sounded like. The...

    That's what my PRT Alpha sounded like. The motors are stepper motors and what you hear is the impulse of each step. Sometimes the sound can be really loud if the steps per second match up with some...
  6. Thread: Hickory Tables

    by paul_z
    Replies
    11
    Views
    8,491

    Outstanding! They will be appreciated for a long...

    Outstanding! They will be appreciated for a long time.
  7. Replies
    5
    Views
    5,531

    The lumberyard where I used to live got a saw...

    The lumberyard where I used to live got a saw stop for free. Their insurance and the state workman's comp each paid half. It was a bargain all the way around.

    Paul Z
  8. Replies
    3
    Views
    4,285

    Sawdust packed under the speed control stopped my...

    Sawdust packed under the speed control stopped my router. Cleaned it out with compressed air and all was well again.
  9. Replies
    1
    Views
    1,653

    Look at what showedup in a web search

    Shopbot Tools - Huge Memorial Day Weekend Sale | lagunatools.com
  10. You might do the reset command. I have had the...

    You might do the reset command. I have had the speed and acceleration values go wonky and cause symptoms like stuttering. I don't remember if the stutter happened in one or both directions.
  11. Replies
    12
    Views
    7,278

    You might try a single flute bit. Paul Z

    You might try a single flute bit.

    Paul Z
  12. Replies
    15
    Views
    7,401

    check this...

    check this http://www.cnczone.com/forums/phase-converters/87669-huanyang-hy02d223b-2-2kw-vfd.html
  13. Replies
    15
    Views
    7,401

    Even with a spindle, you will still have "bit"...

    Even with a spindle, you will still have "bit" noise. It is highly dependent on the bit and type of cut.

    On the plus side, hearing the bit noise will give considerable information about how...
  14. Replies
    2
    Views
    2,708

    There is another, dangerous possibility. You...

    There is another, dangerous possibility. You might have one of the "hot" 3 phase leads hooked to ground. Unless you are certain that you know what you are doing, call an electrician.
  15. "NOT SB related"... but in a way, I think it is. ...

    "NOT SB related"... but in a way, I think it is. Almost all of the people in this forum try to help everyone. It does not matter who or what you are.

    I worked on an Extreme Makeover house where...
  16. Replies
    11
    Views
    6,314

    Awesome!!!!

    Awesome!!!!
  17. Thread: Type 1 PVC

    by paul_z
    Replies
    6
    Views
    5,329

    Joe, Acetal may be double the density of solid...

    Joe,

    Acetal may be double the density of solid PVC. It would be very bad for sign work because almost nothing sticks to it. In a way, it's like polypropylene.

    I am amazed how abrasion...
  18. Thread: Type 1 PVC

    by paul_z
    Replies
    6
    Views
    5,329

    I am curious why you chose PVC for gears. Acetal...

    I am curious why you chose PVC for gears. Acetal (Delrin) might be a much better choice for gears especially if they are going to see heavy use, high temperatures or chemical exposure.

    Paul Z
    ...
  19. Replies
    8
    Views
    7,633

    Did this get resolved? If so, how?

    Did this get resolved? If so, how?
  20. Replies
    8
    Views
    7,633

    Make sure you know what type of machine you have...

    Make sure you know what type of machine you have (PRT Alpha? without the 7.2:1 upgrade?). Type in "UR" and select your machine type. This will reinstall "factory default" values (including...
  21. Replies
    12
    Views
    29,247

    I also found her to be of great help!

    I also found her to be of great help!
  22. Replies
    23
    Views
    12,349

    You might try this instead : Amana Tool MR0102...

    You might try this instead : Amana Tool MR0102 Flush . I use the bit in a battery powered laminate trimmer.

    It will cut the tabs flush and takes very little time. The bit that creates the tabs...
  23. Replies
    2
    Views
    2,115

    Nicely done. Both the booth and the $.

    Nicely done. Both the booth and the $.
  24. Replies
    6
    Views
    3,621

    I find the real one much more impressive. Paul...

    I find the real one much more impressive.

    Paul Z
  25. Replies
    10
    Views
    10,688

    That's pretty much the same collector that I...

    That's pretty much the same collector that I have. Did you take the "Y" off and check the grate behind it? I have had clogs form there.

    Paul Z
Results 1 to 25 of 434
Page 1 of 18 1 2 3 4