Search:

Type: Posts; User: cradke0419

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. I just cut out about 20 sheets of plywood for...

    I just cut out about 20 sheets of plywood for cabinet parts using ecabinets and the spindle shutoff each time like it should. Used vcarve and it would not shutdown
  2. Colombo spindle with delta vfd not shutting off after cut

    I have issues with the spindles shutting off after it is done cutting a file. I have 2 Colombo spindles with delta vfds. I pushed the mode button on the spindle and it goes to a different number...
  3. Want to make a topographic map of my area

    Hello I am looking to try making a topographic map of my area. I am not very good with vcarve pro yet but I'd like to try. Any suggestions on how to get started and what material to use. I am...
  4. Replies
    10
    Views
    4,156

    Thanks for all the replies and help so far. I do...

    Thanks for all the replies and help so far. I do appreciate it
  5. Replies
    10
    Views
    4,156

    I have since changed my dadoes to be .035 to make...

    I have since changed my dadoes to be .035 to make them fit good. Looking at the fit I know something isn't right because there is not 1/32" of slop in the joint. I set my plywood to .48 and my...
  6. Replies
    10
    Views
    1,335

    Right now I'm setup to zero off top of material. ...

    Right now I'm setup to zero off top of material. I am wondering how to change that to go off the bed so I don't have to rezero when I change material thickness. Does it have something to do with...
  7. Replies
    10
    Views
    1,335

    Thanks that helps to see what other people do. I...

    Thanks that helps to see what other people do. I use a 3/8" bit for outline and dadoes in the z axis and have a 5mm in the a axis.
  8. Replies
    10
    Views
    4,156

    I changed some settings and now it's much better....

    I changed some settings and now it's much better. It was set to .01 and I changed them to .025 and it's good. Thanks again for your help
  9. Replies
    10
    Views
    4,156

    Thanks a lot for your help I will mess with it...

    Thanks a lot for your help I will mess with it tonight.
  10. Replies
    10
    Views
    4,156

    Dadoes are too tight

    My dadoes are too tight was wondering where to change the tolerance. Thanks
  11. Replies
    10
    Views
    1,335

    Sounds good thanks Tim

    Sounds good thanks Tim
  12. Replies
    0
    Views
    287

    Z axis doesn't turn off after cutting

    I have a Colombo spindle 2.2 hp with a Delta vfd. The spindle doesn't shut off after cutting with it. It kinda slows down but very minimal. The a axis does turn off after cutting. Any ideas. ...
  13. Replies
    10
    Views
    1,335

    Sorry for all the questions but I have a couple...

    Sorry for all the questions but I have a couple more now. I want to do 2 passes on all of the cuts. Do I set that up by choosing max penetration less than my materials or will that set how deep...
  14. Replies
    10
    Views
    1,335

    I'm also wondering how to post pictures on here

    I'm also wondering how to post pictures on here
  15. Replies
    10
    Views
    1,335

    Setting up shopbot link

    I am trying to setup my shopbot link for cutting 1/2" plywood and 3/4" plywood. I have 2 spindles the z has a 3/8" spiral and the a has a 5mm for drilling. I am lost right now and could use some...
  16. Looking for a basics video on shopbot link

    I have a shopbot with ecabinets. Been using it for a few years but not very often. Computer crashed and now I'm trying to reset everything. Would like to have a basic video of setting up all the...
  17. Replies
    2
    Views
    1,385

    Thanks I checked it out a.s To handle ...

    Thanks I checked it out a.s

    To handle

    Thanks I checked them out and I think it will work. I want to try making some custom mud flaps for a semi hopefully this will work. thanks
  18. Replies
    2
    Views
    1,385

    Laminated plastic sheet for sign making

    Looking for plastic sheets that are laminated with different colors. I would use them for sign making so maybe 1/4 to 3/8" thick and 48"x96"
  19. Yeah I was able to pull up the c6 and c7 command...

    Yeah I was able to pull up the c6 and c7 command but I'm not sure what it is supposed to look like. I would load a picture but I am not sure how to do that
  20. I went to the c drive and looked up the custom...

    I went to the c drive and looked up the custom files but I'm not sure what I am looking at. Anywhere I can look to learn more about this?
  21. Spindles won't turn off when cutting is done

    I have a shopbot alpha 2004 and use vcarve pro. It has two Colombo spindles and when I setup a file to run it will not turn off the spindle when that head is finished. Example- if I use the z head...
  22. Pic of sb3

    I am having trouble getting a picture of the program loaded. It reads x 7.08 y -.125 and that it the center of the a axis to 0,0
  23. I believe I have this setup correctly now. Is...

    I believe I have this setup correctly now. Is there a way to check to make sure I have it correct? I zeroed the z center axis to the bed
    Then I moved the a axis to center on 0,0 and came up with...
  24. A axis isn't correctly lining up with z axis

    I have a 2004 Alpha 4x8 with two Colombo 3 hp spindles. It is normally used on ecabinets to cut out cabinet boxes. I noticed a while back that my shelf holes were not lining up correctly where they...
  25. Replies
    11
    Views
    2,834

    I have a Norwood mx34. Nice machine. I owned a...

    I have a Norwood mx34. Nice machine. I owned a smaller Norwood before with only a 13hp engine and smaller cut . We upgraded to a bigger machine with a 23hp within 2 years. Still not enough power...
Results 1 to 25 of 31
Page 1 of 2 1 2