Search:

More plumbing to complete the project.
Over the electronics and out to the left side to the Fein vacuum.
Give yourself a nice 2" PVC coupler and your fein hose will fit right in.

You will...

Now it is time to mount the table.
A simple trick is to put some bolts in the support angles and then place the board on top.
Give it a quick whack with your deadblow hammer and now you know where...

Next I had to cut the PVC elbow to provide a nice tight "S" curve.
I needed to minimize the spacing between the elbows, but still allow enough height between the bottom of the table and the top of...

After I trial fit, I noticed that the 24" span of plywood could use a bit a support across the middle. So I went back to my favorite HD store and got a piece of 2x2x1/8" aluminum angle and made a...

My vacuum is based on 1" PVC ... The largest size that was still small enough for the air to go under the table and up the back with interfering with spindle carriage without any loss in the Y axis....

I used to own a big PRTAlpha for many years, but I had to sell it so I can move, and bought a desktop last year, but dust collection and vacuum table on this desktop have been a big challenge. I...

A zip of the "C:\sbpart\Quick Setup Guide" folder...
Looks like it contains....

"Basic Deck Rabbet Profile.sbp"

also the video at
...

Been wracking my brain on this one...

The Destkop Quick Start Guide and the training videos reference some files in

c:\sbparts\Quick STart Guide

I do not have that folder, I have...

Brady's link was what I was looking for.... THANKS All!!!

Easy Off oven cleaner and 5 minutes of wait time.

I have seen picture of a hold down (holddown) that is L shaped .... screwed to MDF near the 0,0 corner.... and then another L with a wedge in the upper right corner to hold. Seems like it was made...

Joe,
What was on the end of the drill.

Hello my name is Pat, its been 2 years since my last shopbot...

2 years ago, I moved to Washington to go work for XBOX/Microsoft.
I had to sell my PRTAlpha (to Tony Hazen) that was all...

Love my 18" rikon. Buddy pre-purchased a 14" for this Saturday's saw at wood craft

Kevin,

$5K for an indexer is just silly.

I really like my 18:1 geared setup, I'm into it about $150 gecko, $100 Power Supply, PK296 with mount $300, a little machining and hacking and I am...

Cherry!

(im) patiently waiting for aspire v2.5....

-- pat

Gene,
Looking at the picture on the right... I really like the carved "edge".

What material is this?

-- Pat

what software?

A two rail sweep projected onto radial axis, followed by flutes from "ShopBot Tools->Indexer" ??

-- pat

what software?

Does anybody have a link to the 3.5.<latest>?

I have 3.5.3, 3.5.8, and 3.5.12 saved away.

-- pat

B is always degrees.
My "special program" will allow me to scale any x,y based .sbp file to any amoun of rotation.

To get the exact 1" movement. YOu can setup your model to have the "height"...

To hold down porous stuff, volume is your friend. In Idaho, I draw 5" vaccuum with a fein and can hold most things > 40 sq in.

To hold smaller stuff you need more vaccuum.

-- pat

Jack,
Ummm... You should have gone for the 30"...

http://h10010.www1.hp.com/wwpc/us/en/sm/WF05a/382087-382087-64283-72270-3884471-3297215.html

I run a software development lab at HP. ...

I saw this again today
Numbers moving on the screen, but no physical movement... It actually looks like the motor drivers game up as the axis was not "locked" (I could easily move it by hand) while...