Search:

Type: Posts; User: angelosart

Page 1 of 4 1 2 3 4

Search: Search took 0.25 seconds.

  1. Replies
    0
    Views
    553

    Shopbot Owner in Massachusetts

    Hello,

    Looking for a 4' x 8' shopbot owner in Massachusetts?

    Angelo
  2. Replies
    3
    Views
    1,828

    Cory, Thanks for the info. I will need to...

    Cory,
    Thanks for the info.

    I will need to make a profile cut for some pieces. With wood, I've always left about .01 material and popped out the pieces afterwards. What can I do for aluminum and...
  3. Replies
    3
    Views
    1,828

    Corian & Aluminum 1st timer

    I have never cut corian or aluminum before on my shopbot buddy.

    1/2" Corian, need to use 60deg V-bit & 1/4" straight for profile
    suggestions on bit?
    speeds?
    can I use a skin cut for profile...
  4. Replies
    2
    Views
    951

    Seeking and open book model

    I am seeking and open book model that will work with Aspire 3.5. I have found some models online but they do not have the right extension to work with 3.5. Here is an example of what I'm looking...
  5. Replies
    2
    Views
    5,365

    I apologize. I'm located in north central...

    I apologize. I'm located in north central Massachusetts. Southern NH or Vermont locations would work as well.
  6. Replies
    2
    Views
    5,365

    Massachusetts

    I need a Shopbot owner with at lease a 4'x8' bed to carve a sign for me. I already have the sign laid out in aspire and I have the sbp cutting files. I do not have a Shopbot large enough to do the...
  7. Replies
    4
    Views
    17,189

    Loss of Y then Y&Z

    Ok this will be a hard one to explain.

    Here is the scaled down attempt

    Was cutting a large 3d file (about 5hrs) with .0321 ball nose bit, speeds 5,3...

    1) Lost Y position intermittently (see...
  8. Replies
    3
    Views
    2,655

    Hi Scott, Thanks for the quick response. I...

    Hi Scott,

    Thanks for the quick response. I hit dxf, now what do I do, nothing happened

    Angelo
  9. Replies
    3
    Views
    2,655

    Convert file to DXF?

    I own a shopbot cnc and purchased the Aspire software with it. When I go to save the machining file it does not contain a dxf extension choice. Can I convert one of the extensions to a dxf file?
  10. Replies
    3
    Views
    8,082

    Thanks. It was the fuse.

    Thanks. It was the fuse.
  11. Replies
    3
    Views
    8,082

    Fuse or Relay?

    Hello,

    I have an SB 32 standard Buddy. I went to surface a piece of wood today and had the z zero off the spoilboard not the top of the wood. (Thank me very much) The surfacing bit gouged right...
  12. Replies
    1
    Views
    13,171

    Sell dxf files?

    Does anyone know where you can sell your dxf files online?
  13. Thread: Vaccuum Jig

    by angelosart
    Replies
    3
    Views
    6,807

    Vaccuum Jig

    Has anyone ever tried this vacuum jig for small piece hold down/clamp on their SB?

    http://www.joewoodworker.com/veneering/vacuumclampingmatrix.htm
  14. Replies
    3
    Views
    2,814

    Thanks for your help guys. It stumped me all...

    Thanks for your help guys. It stumped me all night, was driving me crazy. And guess what.... the measuring tape I was using after the cut was off!!!! Unbelievable. Check EVERYTHING Boys &...
  15. Replies
    3
    Views
    2,814

    Profile 1/8" Off?

    I have a SB Buddy Standard 32". I noticed that my outside profile cuts are off by 1/8" smaller. I triple checked my numbers, cut 3 more profiles and they were all off by 1/8".

    Using:
    1/4" bit...
  16. Replies
    1
    Views
    5,244

    Buddy Surface Board Off

    I have had my buddy standard 32 for more than 3 yrs. PC router. I tried 3X to surface my spoilboard and each time I get .005 difference from ine end of the X axis to the other end. The variation...
  17. Replies
    5
    Views
    3,633

    Hi Jim, Can you tell me why? What antivirus...

    Hi Jim,

    Can you tell me why? What antivirus software do you use?

    A
  18. Replies
    5
    Views
    3,633

    Anti Virus software & SB control

    Hello,

    I wasn't sure where to post this. A couple of years ago I used to have Norton anti virus but it was now and then interfering with the SB control and operation of the CNC machine. Have...
  19. Replies
    0
    Views
    6,684

    Consistent Ridges

    Hello,

    I seem to keep getting this sort of ridging along the same X axis in the last few projects. See photo below. Its not hard to scrape or sand out but any idea why? I just changed my...
  20. Replies
    3
    Views
    4,432

    Hii Tim, I checked both x and y limit switches...

    Hii Tim,

    I checked both x and y limit switches and from what I can tell the connections are solid and the wire/cable looks good.

    Thanks
    Angelo
  21. Replies
    5
    Views
    6,110

    Hi Tim, The entire cutting file. It rasters...

    Hi Tim,

    The entire cutting file. It rasters along the x axis. It starts on the far end of the x axis and works toward 0. I would like it to start from 0 and raster along the x axis toward the...
  22. Replies
    5
    Views
    6,110

    Hi Kyle, I might not have explained myself...

    Hi Kyle,

    I might not have explained myself correctly. I want the rough cut to go from left to right along the x axis not right to left. I tried changing the datum point but that didn't work...
  23. Replies
    3
    Views
    4,432

    inputs 2 & 3

    I've run a rough cut 3 times now and before the cut is completed the my Buddy cut out--I get a "quit" window and inputs 2 & 3 get a red x in the center. I've already run about 1/2 the file and I...
  24. Replies
    5
    Views
    6,110

    Rough Start point?

    Is there a way of changing the starting point on a rough cut? I have a rough cutting toolpath that starts at 23,0 and moves along the Y axis. I want to be able to start at 0,0 and move along the Y...
  25. Replies
    7
    Views
    5,341

    First thanks for the help and responses. This...

    First thanks for the help and responses.

    This was not happening the day before, it had just started. First time its ever happened. Took a measurement on the surfacing bit and noticed a chip on...
Results 1 to 25 of 100
Page 1 of 4 1 2 3 4