Search:

Type: Posts; User: wayne fussell

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    15
    Views
    9,793

    Andy, I too thought that probing would be the...

    Andy,
    I too thought that probing would be the way to go. Found out really fast or slow, depending on how your looking at it, that probing a part takes a very long time.
    Example, One part i probed...
  2. Replies
    8
    Views
    4,957

    And I will take out the MH

    And I will take out the MH
  3. Replies
    8
    Views
    4,957

    Thanks Brady I did change the safe Z to 2" for...

    Thanks Brady
    I did change the safe Z to 2" for that reason.
  4. Replies
    8
    Views
    4,957

    Brady, Is this anywhere close to what I'm...

    Brady,

    Is this anywhere close to what I'm looking for? For a part file of course.

    zero material at center

    MH, 'move to o,o in X,Y,;with safe-Z pull-up

    J2,new x=6.5,y=4.3
  5. Replies
    8
    Views
    4,957

    in the command section, got it. Guess I need to...

    in the command section, got it.
    Guess I need to learn how to write a simple SB code.:eek:
  6. Replies
    8
    Views
    4,957

    I think I understand. but where does this get...

    I think I understand.
    but where does this get typed in?

    Type the following into SB3:
    SO,1,1 'Turns on router
    MZ, .225 'Moves Z down
    MB,360 'Move indexer 1 revolution
    JZ,1 'Jog Z up to safe...
  7. Replies
    8
    Views
    4,957

    wrapping around a cylinder

    Can somebody point me in the right direction.
    I need to cut a half round groove in a cylinder. Brady has written instructions for me but I'm not having much luck.
    The cylinder diameter is .95" ...
  8. Replies
    10
    Views
    4,141

    Ron, I got it. Dummy Me,:eek: went back and read...

    Ron,
    I got it. Dummy Me,:eek: went back and read the posts again and saw "edit the ones in red".:rolleyes:

    Guess I should have read it a little more careful.
  9. Replies
    10
    Views
    4,141

    X=-3.105 Y=-6.913 Z=2.0 I need the Z to raise...

    X=-3.105
    Y=-6.913
    Z=2.0 I need the Z to raise to this height after Zzero, this way it does not crash into the indexer.

    These are the numbers I need. But before I get too confused and plug them...
  10. Replies
    10
    Views
    4,141

    'These values are used in the ZZero routine...

    'These values are used in the ZZero routine
    &my_hasZzero=1
    &my_ZzeroThickness=0.121
    &my_ZzeroInput=1
    &my_ZzeroSafeZ=2.0


    Is this correct?
  11. Replies
    10
    Views
    4,141

    So this would be what I'm looking for? 'These...

    So this would be what I'm looking for?

    'These values are used by the XYZero program
    &my_hasProx=1
    &my_XYzeroSafeZ=1
    &my_XYzeroOffsetX=-3.105
    &my_XYzeroOffsetY=-6.913
    &my_XYzeroOffsetZ=1...
  12. Replies
    10
    Views
    4,141

    Hey Ron If I need to raise the Z to a safer...

    Hey Ron
    If I need to raise the Z to a safer height, say 2" it would be done there also?
  13. Replies
    10
    Views
    4,141

    Thanks Ron, That's easy enough. I knew there was...

    Thanks Ron, That's easy enough.
    I knew there was a way.
  14. Replies
    10
    Views
    4,141

    X & Y position

    I need a little help.
    I'm using a buddy with a PC router for reference.
    I always cut the same parts from same position on an indexer. I have read through the manual, but for me that might as well...
  15. Replies
    41
    Views
    18,083

    One picture 17712

    One picture

    17712
  16. Replies
    41
    Views
    18,083

    I am having one small issue that maybe somebody...

    I am having one small issue that maybe somebody could help with.
    While cutting the blade I get a little chatter from the bit or wood, not sure which.
    using a 1/8 ball nose
    16000 rpm at 1" per...
  17. Replies
    41
    Views
    18,083

    After a frustrating couple of weeks we are almost...

    After a frustrating couple of weeks we are almost where we need to be with cutting the first propeller.
    Using DeskProto for the CAM software. The only problem I'm having right now is the cut a just...
  18. Replies
    9
    Views
    4,868

    :DJust ordered it Brady, Thanks for the help.

    :DJust ordered it Brady, Thanks for the help.
  19. Replies
    9
    Views
    4,868

    Yes I did Brady! I'll have to call them to get...

    Yes I did Brady! I'll have to call them to get the length.
  20. Replies
    9
    Views
    4,868

    Thats what I'm looking for, a Steb Center. But it...

    Thats what I'm looking for, a Steb Center. But it has to be as short as possible because of the buddys table. unless I use the 6' stick.
  21. Replies
    9
    Views
    4,868

    Thanks Brady, just found the Penn state one.

    Thanks Brady, just found the Penn state one.
  22. Replies
    9
    Views
    4,868

    indexer spur center

    Anybody have any Ideas where to get a headstock spur center thats fits?
  23. Replies
    41
    Views
    18,083

    Took me about 3 tries to get the scaning started...

    Took me about 3 tries to get the scaning started but I got it figured out. Now I am waiting for the indexer. I'm going to do a complete scan of the front of the blade on tuesday. If my figures are...
  24. Replies
    41
    Views
    18,083

    Sunday I'll attach the spoil board and fully get...

    Sunday I'll attach the spoil board and fully get it surfaced.

    Had a few issues with the Z routine, but I got that figured out after watching the video again.
    Lots to learn.
  25. Replies
    41
    Views
    18,083

    17323 17324 17325 My Buddy and its first...

    17323

    17324

    17325

    My Buddy and its first cut. Kool
Results 1 to 25 of 39
Page 1 of 2 1 2