Search:

Type: Posts; User: srwtlc

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Switch#4 STOP Type should be set to Normal Closed...

    Switch#4 STOP Type should be set to Normal Closed Stop. If it doesn't work when set that way, make sure your E-Stop button is reset (twist and popped out). Sometimes the contacts get dirty and...
  2. Don't look at the larger board, you need to see...

    Don't look at the larger board, you need to see what's on the smaller "Controller board" that is standing vertical.
  3. I'm pretty sure you can use the latest version,...

    I'm pretty sure you can use the latest version, 3.8.50. Look on this page and click the tab on the right to see how to verify your version of control card. ...
  4. Thread: PRSstandard

    by srwtlc
    Replies
    18
    Views
    2,263

    Perhaps instead of saying "Update", just say...

    Perhaps instead of saying "Update", just say "Bump", since you're really not updating anything, but just bumping it to the top of the list again.
  5. Thread: x stepper motor

    by srwtlc
    Replies
    12
    Views
    514

    Hey Cowboy, Is it a continuous tick tick as it...

    Hey Cowboy,

    Is it a continuous tick tick as it moves in one direction or just a tick tick you can hear by manually push/pull on the carriage/table or when it's changing direction (a lot of this in...
  6. Replies
    5
    Views
    352

    Wayfair employees

    Just when you think liberals have reached the pinnacle of idiocy, they train up a bigger idiot (group of idiots)! I guess that they would rather the ILLEGAL immigrant children sleep on the concrete...
  7. Replies
    15
    Views
    869

    Ha Ha, which wire should I cut? The blue one! ...

    Ha Ha, which wire should I cut? The blue one! *BOOM* ;)
  8. Thread: FABMO Status

    by srwtlc
    Replies
    25
    Views
    2,313

    Why doesn't someone at SBHQ go ahead and update...

    Why doesn't someone at SBHQ go ahead and update the Fabmo Demo Page? Let the customers see what it is and how it works, see the work flow and controls. I know it can be done, just set it up on your...
  9. Replies
    5
    Views
    458

    Not sure if you could tie it to the spacebar...

    Not sure if you could tie it to the spacebar (imagine there's a way, just haven't delved into it), and #4 is used for E-Stop, so that will drop everything. Either way, your chances of resuming...
  10. Thread: FABMO Status

    by srwtlc
    Replies
    25
    Views
    2,313

    Chuck, all the info you're looking for as to...

    Chuck, all the info you're looking for as to purchasing a replacement system is here... http://centroidcncforum.com/viewtopic.php?f=62&t=2147&start=10

    If you are wanting to go the DIY route,...
  11. Thread: FABMO Status

    by srwtlc
    Replies
    25
    Views
    2,313

    You can check out FabMo here...

    You can check out FabMo here.
  12. Thread: FABMO Status

    by srwtlc
    Replies
    25
    Views
    2,313

    No real info/updates for you Jim, but I stopped...

    No real info/updates for you Jim, but I stopped beta/release candidate testing it more than 6 months ago and by checking the Github site for it every so often, I've seen little to no...
  13. Replies
    5
    Views
    721

    Commitment, what's that?! ;)

    Commitment, what's that?! ;)
  14. Replies
    10
    Views
    708

    The easiest way to do an air cut is to choose 3D...

    The easiest way to do an air cut is to choose 3D offset in the fill-in sheet when loading a file. First, raise the z axis high enough to keep all depth of cuts above your material and choose 3D...
  15. Hey Scott, I just spray a coat of precat...

    Hey Scott,

    I just spray a coat of precat lacquer to seal them (maybe a little extra on the relief), then some Van Dyke Brown glaze in the relief and black spray ink in the letters after masking...
  16. Yup, forgot to say that the finish toolpath...

    Yup, forgot to say that the finish toolpath always goes full depth. You could trick it by setting the Z higher, but that's what the roughing pass is there for. :)
  17. Too much wasted time, just use the 3D roughing...

    Too much wasted time, just use the 3D roughing toolpath and use a 0.25" downcut end mill (not a ballnose) at 48-50% stepover with a machining allowance of 0.04" and up to 0.375 per pass depending on...
  18. Replies
    21
    Views
    1,458

    That is some beautiful grain! What, no pic of...

    That is some beautiful grain! What, no pic of the track carnage? :) Glad you weren't hurt!
  19. Replies
    6
    Views
    497

    3.6.46 doesn't have that option. Try right...

    3.6.46 doesn't have that option.

    Try right clicking in the blank area of the menu or icon area and choose customize. See if "Menu Bar" and "Standard" are checked in the toolbars tab, Try the...
  20. Verify moisture content, it should be 6-8% if...

    Verify moisture content, it should be 6-8% if kiln dried. Air dried will be around 14% or so and can be unpredictable depending on your climate. Try a bit narrower boards for the glue up (3" or...
  21. Replies
    21
    Views
    1,458

    Only seen some ads, but the Kreg unit doesn't...

    Only seen some ads, but the Kreg unit doesn't look bad either.
  22. Thread: other hardware

    by srwtlc
    Replies
    4
    Views
    440

    Check out Centroid Acorn...

    Check out Centroid Acorn or UCCNC. All options will require some other hardware to get going, but much less than your first thought. Mach3 is deadware. UCCNC is more like Mach3, but Centroid Acorn...
  23. Thread: New Spindle

    by srwtlc
    Replies
    15
    Views
    928

    I haven't checked with anyone yet, but Ekstrom...

    I haven't checked with anyone yet, but Ekstrom Carlson in Rockford Illinois supposedly does.
  24. Thread: New Spindle

    by srwtlc
    Replies
    15
    Views
    928

    They contacted the factory and replied back to me...

    They contacted the factory and replied back to me that the new model now has the connection box as shown in my video and that they had an older picture in the add. Who knows!? You could try one of...
  25. Thread: New Spindle

    by srwtlc
    Replies
    15
    Views
    928

    This was the supplier...

    This was the supplier I ordered it from. As you can see in the ad, it has the connector we would like for plugging it right in, but according to what they told me, the newer ones from the factory...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4