Search:

Type: Posts; User: Brady Watson

Page 1 of 20 1 2 3 4

Search: Search took 0.12 seconds.

  1. Yeah really. I don't check the forums often and...

    Yeah really. I don't check the forums often and it seems like every time I look there's a new post from Jerry whining in one form or another. It's bordering on psycho/stalker at this point.

    I...
  2. Replies
    23
    Views
    6,344

    Eric, The bell is about 34.5" in diameter and it...

    Eric,
    The bell is about 34.5" in diameter and it is about 30.25" tall. IC3D in Ohio printed it.
  3. Replies
    23
    Views
    6,344

    Thanks Scott - yes, the scanner DID pick up the...

    Thanks Scott - yes, the scanner DID pick up the nicks etc, but I sculpted them out to make printing faster and more reliable.

    When you print at this scale, the size of the nozzle and filament...
  4. Replies
    23
    Views
    6,344

    Here's a time lapse: https://youtu.be/Bs7etPCJ78g

    Here's a time lapse: https://youtu.be/Bs7etPCJ78g
  5. Replies
    23
    Views
    6,344

    Update!

    Here's an update for those following this thread. I just received pics from the USS NJ Museum showing the original bell that I scanned and the replica that was printed full scale by IC3D in Ohio. The...
  6. Replies
    4
    Views
    622

    Welcome Bill

    Welcome Bill
  7. Replies
    6
    Views
    1,243

    No it's not just you & it is not version...

    No it's not just you & it is not version specific. Some releases just work better on some tools than others. My advice would be to revert to whatever version you were using previously. For instance,...
  8. For real... cutting anything off would detract...

    For real... cutting anything off would detract from it!
  9. Replies
    3
    Views
    815

    Reinstall the firmware via UI. Then do a UR and...

    Reinstall the firmware via UI. Then do a UR and be sure to pick the right machine configuration.
  10. Very good. You're welcome. Hopefully you get to...

    Very good. You're welcome. Hopefully you get to the bottom of why it is triggering the e-stop.
  11. Tracy, When inputs get unreliable or flaky it's...

    Tracy,
    When inputs get unreliable or flaky it's been my experience that the controller card is starting to go.

    My advice would be to open the control box, remove the 4 Phillips screws holding...
  12. Tracy, The computer is a very important part of...

    Tracy,
    The computer is a very important part of the SB controller. From what you mention, it could be either slow communication speed between the PC and the control box (USB) or something as simple...
  13. Tracy, There are many things that can cause the...

    Tracy,
    There are many things that can cause the situation you describe. For instance (and assuming this is an Alpha), if your 24v power supply is intermittent or flaky, it can cause weird things to...
  14. Replies
    16
    Views
    3,512

    "Cactus Juice resin" is pretty popular for...

    "Cactus Juice resin" is pretty popular for stabilizing wonky lumber...
  15. You should be in the 8 to 12% stepover range. So...

    You should be in the 8 to 12% stepover range. So a 1/32" ball should leave no raster lines with a stepover value of .0025 to .00375 inches.

    Start with a 12% and run about 1/2" of the file. How...
  16. Replies
    22
    Views
    3,782

    You're really missing out on what your machine is...

    You're really missing out on what your machine is capable of by not running some kind of gear/belt reduction to gain mechanical resolution. By replacing the closed loop nature of the Alpha motors...
  17. Replies
    22
    Views
    3,782

    Mailbox empty now...

    Mailbox empty now...
  18. Replies
    22
    Views
    3,782

    No, You don't want that gearbox. Check your PM....

    No,
    You don't want that gearbox. Check your PM. You'll ultimately need the gearboxes, motor swing plates and compatible pinions.
  19. Replies
    11
    Views
    1,923

    Rest in peace my friend.

    Rest in peace my friend.
  20. Replies
    10
    Views
    4,612

    Chuck, There's really no set price window for...

    Chuck,
    There's really no set price window for used pumps. When I bought my Becker ($10k new), I paid like $1500 for it (used from Boeing...so it was maintained well) but it cost me like $1200 to get...
  21. Replies
    1
    Views
    939

    I don't know if you need a 1/4" tool or if you...

    I don't know if you need a 1/4" tool or if you can go larger. It looks like the right tool for the job is either a 2 or 3 flute spiral-O, but it doesn't look like Onsrud offers it in a length of cut...
  22. Replies
    7
    Views
    1,351

    ADA signs are made by inserting the balls into...

    ADA signs are made by inserting the balls into the plate. Do some googling...
  23. Replies
    2
    Views
    1,526

    Yes. Have a look in your Shopbot binder or comb...

    Yes. Have a look in your Shopbot binder or comb through email for one of your first messages from Dianne
  24. Replies
    31
    Views
    9,676

    Latest info regarding Shopbot Edition:...

    Latest info regarding Shopbot Edition: http://www.talkshopbot.com/forum/showthread.php?25156-Info-on-upgrading-VCarvePro-ShopBot-Edition-to-VCarvePro-v10&highlight=Shopbot+edition
  25. Andy Glad to help. No need to be humble for...

    Andy
    Glad to help. No need to be humble for me... I'm just a regular guy.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4