Search:

Type: Posts; User: erniek

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Edgebander

    by erniek
    Replies
    1
    Views
    354

    Edgebander

    Anyone know where I could get a service manual for my Holzher 1405 Edge bander? I'm doing a job with high gloss panels and want to get the second set of trimmers going.
  2. Replies
    22
    Views
    5,804

    I like to use 1/4" compression bits on my PRT. ...

    I like to use 1/4" compression bits on my PRT. Cutting speed I use is 4-4.5 IPS with at 10800 rpm. I'm sure it the bits could be faster on an alpha machine but any faster and I'm risking losing...
  3. Thread: Dovetail joints

    by erniek
    Replies
    1
    Views
    4,565

    Dovetail joints

    Has anyone used the dovetail joints feature of ecabinets? Is that even possible with a shopbot?
  4. Thread: Tabbing

    by erniek
    Replies
    8
    Views
    5,812

    If I'm cutting some smaller parts I'll spray some...

    If I'm cutting some smaller parts I'll spray some contact cement on the spoil board, let it dry then put the sheet down. Seems to help a lot. Mind you you have to get amount of contact cement and...
  5. Replies
    2
    Views
    1,829

    Yeah looks like the graphical design is the way...

    Yeah looks like the graphical design is the way to go with this. Trying to do the offset mathematically is proving difficult. I did like the spreadsheet programming method though. Gives me much...
  6. Replies
    2
    Views
    1,829

    Arches for MDF Raised Panel Doors

    I've had good success making raised panel looking MDF doors using a cove bit, a pointed beaded bit for the inside of the frame and a small endmill bit using 5 passes. Now I'm considering trying to...
  7. Replies
    2
    Views
    1,929

    Too many Variables?

    Recently I was having intermittent problems with my tool change routine.
    I have a "Z" axis with a 1/4" cutter and an "A" axis with a 5mm cutter drilling holes. At the start of cutting, instead of...
  8. Thread: Edge profiles

    by erniek
    Replies
    3
    Views
    3,368

    door / drawer parts

    I have been able to cut slab doors with or without edgebanding and also drawer box parts. Haven't tried the dovetail joints though.
  9. Replies
    20
    Views
    7,370

    I had random limit switch triggers happening once...

    I had random limit switch triggers happening once in a while too. Then a few months later the limit switch sensor broke in half for no apparent reason. Made me think that the sensor was defective...
  10. Thread: 3" Radius Edge

    by erniek
    Replies
    14
    Views
    3,864

    Steve, interesting way to do that with and with...

    Steve, interesting way to do that with and with an endmill bit as well.
    I will keep it in mind if the job comes my way.
  11. Thread: 3" Radius Edge

    by erniek
    Replies
    14
    Views
    3,864

    Thanks for all the advice, guess I'm gonna have...

    Thanks for all the advice, guess I'm gonna have to learn ArtCam a bit better.

    Steve M. I don't think I can raster 90 degrees to the edge as I only have a 3 axis machine.
  12. Thread: 3" Radius Edge

    by erniek
    Replies
    14
    Views
    3,864

    I have artcam, ecabinets and autocad. I'm...

    I have artcam, ecabinets and autocad. I'm thinking the thickness may be an issue as well. I may have to move my spindle up higher if that's possible and get a 4" long bit. The only thing I've seen...
  13. Thread: 3" Radius Edge

    by erniek
    Replies
    14
    Views
    3,864

    3" Radius Edge

    I've been asked to build a circular sign with a 3" radius quarter round edge.

    How is the best way to program cutting that edge since there's no such thing as a 3" radius router bit.

    I'm...
  14. Thread: Edge profiles

    by erniek
    Replies
    3
    Views
    3,368

    Edge profiles

    Has anyone been able to use the edge profile feature of ecabinets and cut it out with the link on a shop bot?
  15. Replies
    8
    Views
    2,251

    I had a similar problem, couldn't figure it out....

    I had a similar problem, couldn't figure it out. Then one day the "Y" axis limit switch sensor broke in half. So I'm thinking that the sensor itself was causing the false limit switch alerts.
  16. Replies
    4
    Views
    2,913

    Just to let you all know, running the file from...

    Just to let you all know, running the file from Thermwood and write protecting the file afterwards has solved the problem.
  17. Replies
    4
    Views
    2,913

    Gary, No I didn't port the old settings to the...

    Gary, No I didn't port the old settings to the new computer, I just re-entered all my settings manually. But thanks for that info.

    Michael, Yes that's the error I'm getting. Thanks for the...
  18. Replies
    4
    Views
    2,913

    Link program Error

    After moving to a new computer, every time I re-boot I get an error message when trying to load a new cutting file with the link. The message is Crypt something or other. To fix it I have to delete...
  19. Replies
    12
    Views
    3,926

    Mortise Compression bits

    I've been getting mine from www.rbtoolsupply.com/ as well. Last time I called them they said they had a harder version that's supposed to last twice as long as their standard carbide. I do find...
  20. Replies
    3
    Views
    1,974

    Thanks Gary

    That worked! Thanks again for the quick response.
  21. Replies
    3
    Views
    1,974

    New Computer not detecting Shopbot

    I just built a new computer with a Gigabyte B75M-D3H motherboard to run the shopbot. It's not finding the Shopbot, I've tried all the USB ports to no avail.

    What process should I go thru to...
  22. Replies
    3
    Views
    2,157

    Thanks Gary

    I just wanted to say thanks for the offer of help and your frequent and prompt response to issues we all have.

    I'm still running with the custom cut files you set up for me a few years back...
  23. Replies
    3
    Views
    2,157

    Problem solved.

    The new version clobbered my custom cut files, thought I had copied them back. I tried again and it's working now.

    Funny thing was I tried to go back to the 3.6.44 version and it wouldn't...
  24. Replies
    3
    Views
    2,157

    Beta Control Software

    Just tried using the beta control software with the link.
    Instead of drilling 0.5" deep holes it drilled all the way thru the
    sheet and 0.5" into the spoil board. Then it didn't retract the...
  25. Replies
    2
    Views
    1,429

    Limit switch sensor.

    Just had my Y-axis sensor break in two. Is this a generic part available
    locally or do I need to order from Shopbot?
Results 1 to 25 of 114
Page 1 of 5 1 2 3 4