Search:

Type: Posts; User: bill.young

Page 1 of 20 1 2 3 4

Search: Search took 0.46 seconds.

  1. I'm not going to get into the middle of this...

    I'm not going to get into the middle of this discussion, but as a moderator I want to comment about posts and if/when they are deleted.

    We have very rarely depleted posts or threads, mostly first...
  2. Replies
    6
    Views
    4,629

    As far as I know all ShopBots have had PWM...

    As far as I know all ShopBots have had PWM control capabilities since the early plasma cutter days. My suggestion would be to check with the ShopBot support folks and find out the details about using...
  3. Replies
    13
    Views
    1,869

    That's definitely a weird one! After warming...

    That's definitely a weird one!

    After warming up does every Z move have a corresponding Y move? When it lifts straight up at the end of the file to its safe Z location does the Y also move, or is...
  4. Replies
    13
    Views
    1,869

    Does it lose position ...cut the part the wrong...

    Does it lose position ...cut the part the wrong size and not return to the correct home position afterwards? Or is it that the tabs are shifted but the parts are correct other than that?
  5. Replies
    6
    Views
    1,000

    I'm sure you have honorable intentions or you...

    I'm sure you have honorable intentions or you wouldn't have posted publicly, and as noted above Vectric has a very fair transfer policy.

    Be aware though that if the original owner has used their...
  6. I got two PRS Alphas with HSD 2.2 spindles in...

    I got two PRS Alphas with HSD 2.2 spindles in 2008 for a big cutting job. One of the spindles was replaced maybe 3 years ago, but the other one is still running fine after 13 years. I don't cut...
  7. Replies
    21
    Views
    2,668

    Have you tried pushing down on the table when the...

    Have you tried pushing down on the table when the vacuum is off, to see if the layers are not bonded together and there's some spring in the lamination?
  8. Replies
    4
    Views
    994

    Hey Kyle, This doesn't really answer your...

    Hey Kyle,

    This doesn't really answer your question, but have you seen the STEM guitar builders website? They seem to have lots of resources for teachers building guitars
    ...
  9. Thread: 3d printer

    by bill.young
    Replies
    22
    Views
    14,765

    I've had a Prusa MK3 for a couple of years and...

    I've had a Prusa MK3 for a couple of years and agree 100%. Was given an Ender 3 that prints well now but has required a ton of fiddling and fussing to get it that way..the Prusa has been trouble free.
  10. Replies
    4
    Views
    948

    3d printing and ShopBotting

    Hi all,

    It appears that there are a fair number of Shopbotters that also have 3d printers. I'm curious if/how you combine 3d printed parts and ShopBot cut parts into the projects you do?

    Here...
  11. Thread: 3d printer

    by bill.young
    Replies
    22
    Views
    14,765

    What do you plan on 3d printing? The Dremel is a...

    What do you plan on 3d printing? The Dremel is a good 3d printer with good reviews, but if you're planning on doing small, high rez prints and don't mind a little resin messiness you might look at...
  12. Replies
    12
    Views
    3,722

    Excellent!

    Excellent!
  13. Replies
    12
    Views
    3,722

    Bob, Support is your best bet for sure, but I...

    Bob,

    Support is your best bet for sure, but I have a somewhat similar setup on my Max and do a lot of turning with it. I don't use the MTC posts though, and have a 3" indexer.

    If you want to...
  14. Replies
    12
    Views
    3,722

    My guess is that the B-axis lost steps. I'd bet...

    My guess is that the B-axis lost steps. I'd bet the depth of cut is different for that feature or the feed speed.

    You could try running that feature without a blank in it and a reference mark on...
  15. Replies
    3
    Views
    2,107

    It's possible that you have a bad driver...only...

    It's possible that you have a bad driver...only moving in one direction is a symptom of that...but the first thing I'd look at is the Y-axis location in the display and see if it's a large negative...
  16. Replies
    7
    Views
    2,187

    My first step when looking for cutting problems...

    My first step when looking for cutting problems is to power up the tool and then grab each moving part...both ends of the gantry, the YZ car, the nose of the spindle... and shake it to see if you...
  17. Replies
    3
    Views
    1,815

    Hey Daniel, Your best bet for getting useful...

    Hey Daniel,

    Your best bet for getting useful info is to contact tech support at ShopBot.

    Bill
  18. Replies
    15
    Views
    10,099

    The standard programming pulses yellow until the...

    The standard programming pulses yellow until the control box connects and then turns solid green. Since any time the tool moves we feel like you need a warning, when the tool is moving with the...
  19. Replies
    15
    Views
    10,099

    We're exploring some options for lights. This one...

    We're exploring some options for lights. This one works well on my PRS and is bolted to the YZ car, and 've just been sticking a straight strip to the gantry beam on my MAX. I'm sure there are some...
  20. Replies
    15
    Views
    10,099

    Sorry...haven't been on the forum much and slow...

    Sorry...haven't been on the forum much and slow to update on this:

    We got the first batch boards and they replace your existing ribbon cable. On the end is a wago connector to attach the...
  21. Replies
    15
    Views
    10,099

    I will check on progress and report back. Bill

    I will check on progress and report back.

    Bill
  22. Replies
    10
    Views
    1,795

    Hey Richard... I checked into it for you and it...

    Hey Richard... I checked into it for you and it looks like ShopBot had sent you a quote that included shipping via UPS for $78.19. Let them know if you didn't get that quote.

    Bill
  23. Replies
    7
    Views
    2,120

    My pleasure.

    My pleasure.
  24. Replies
    7
    Views
    2,120

    Hey Kyle, There is indeed. You can download...

    Hey Kyle,

    There is indeed. You can download the whole shebang from http://www.100kprojects.com/project_pages/Quicklap_Canoe/

    Be aware that the instructions were done before digital cameras and...
  25. Replies
    7
    Views
    2,120

    I must admit I was pretty excited when they told...

    I must admit I was pretty excited when they told me that it was done and in the water. There's even talk that they might build some more for the rest of the grandkids!

    Bill
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4