Search:

Type: Posts; User: khaos

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Replies
    7
    Views
    922

    I'll either help or look like a fool for not...

    I'll either help or look like a fool for not explaining this well. ;)

    First you need to figure out the angle. For discussions sake that looks like a 45* angle. So you need a 22.5*, or half,...
  2. Replies
    6
    Views
    1,652

    Look at prism letters in aspire. Or you can use...

    Look at prism letters in aspire. Or you can use the modeling feature and extrude the letters from the 3d surface.

    Example I did recently using the extrusion method.
    ...
  3. Replies
    27
    Views
    5,897

    Great thread! BLUF: I primarily do 3D work. I...

    Great thread!

    BLUF: I primarily do 3D work. I only share here for the lurkers and not to provide a solution for Brady's application.


    I have to go through spoilboard at a decent clip. I...
  4. Replies
    13
    Views
    2,598

    Indeed. Lovely work.

    Indeed. Lovely work.
  5. Thread: Mini Carousel

    by khaos
    Replies
    2
    Views
    953

    Thats awesome. You have mini makers in those...

    Thats awesome. You have mini makers in those kids now. :cool:
  6. Replies
    5
    Views
    966

    Hypothetically, don't use the bearing. The...

    Hypothetically, don't use the bearing. The danger is breaking the bit, possibly damaging your machine and letting blood out of your blood bag.
  7. Thread: Quality Matters

    by khaos
    Replies
    4
    Views
    1,098

    Hee hee:rolleyes:

    Hee hee:rolleyes:
  8. Thread: Quality Matters

    by khaos
    Replies
    4
    Views
    1,098

    Quality Matters

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=32211&stc=1
  9. Thread: Laser cutting

    by khaos
    Replies
    3
    Views
    2,172

    Sure. The question become ROI. Can you get the...

    Sure. The question become ROI. Can you get the 4th dim to work as expected and still focus the beam as needed and make a profit after you purchase that machine and pay for design software to...
  10. Thread: Laser cutting

    by khaos
    Replies
    3
    Views
    2,172

    Congrats on your first post!! Too bad it was...

    Congrats on your first post!! Too bad it was spam ... :rolleyes:
  11. Thread: Oh noes....

    by khaos
    Replies
    9
    Views
    2,197

    Although. I have a PRS, I recall that issue being...

    Although. I have a PRS, I recall that issue being resolved for me when I grounded the machine to the shop ground with its own strap. I'd try Russ's option first though.
  12. Replies
    5
    Views
    775

    LOL "this sucker" :rolleyes: I see what you did...

    LOL "this sucker" :rolleyes: I see what you did there.

    OK, I admit, I laugh at "That what she said" jokes too.
  13. Replies
    3
    Views
    1,065

    Great tool! Adapt, Improvise and overcome! It...

    Great tool! Adapt, Improvise and overcome! It looks solid and I think the weight is fine for the function.
  14. Replies
    9
    Views
    2,529

    I think you should check out this thread...

    I think you should check out this thread:

    fwiw I'm with Brady on this.
  15. Thread: Sea Dek

    by khaos
    Replies
    4
    Views
    867

    I used a 2 flute endmill 4in/sec @ 13K .125 passes

    I used a 2 flute endmill 4in/sec @ 13K .125 passes
  16. Replies
    4
    Views
    784

    Following with interest. I have interest in the...

    Following with interest. I have interest in the ability to cut 16th" myself.
  17. Thread: Sea Dek

    by khaos
    Replies
    4
    Views
    867

    There has been a mix. It cut like butter for me...

    There has been a mix. It cut like butter for me but for Mark D. it was a nightmare with chipping and horrible cuts. We used basically the same bits and feed and speeds. I know "Sometimes its good"...
  18. Replies
    24
    Views
    5,533

    Sounds great. Keep us informed. :)

    Sounds great. Keep us informed. :)
  19. Replies
    24
    Views
    5,533

    I can only imagine just how stunning that is in...

    I can only imagine just how stunning that is in person!! Perhaps you can make an open coffee table or such with a bottom shelf that is a mirror. Then you would see both sides.
  20. Replies
    49
    Views
    13,314

    EF3 lol So nice.

    EF3 lol So nice.
  21. Replies
    6
    Views
    1,503

    Looks cool. I've been thinking about making some...

    Looks cool. I've been thinking about making some pontoon boat furniture in that type of design from extruded pvc. No rot, easy to clean with a pressure washer.
  22. Replies
    49
    Views
    13,314

    Thanks! That's pretty damn awesome. I noticed...

    Thanks! That's pretty damn awesome. I noticed the big meat in the youtube video and felt all inadequate lol. A billet head for my freestyle jet ski is in my future.
  23. Replies
    49
    Views
    13,314

    That's nice work. Would you share Bits, feeds and...

    That's nice work. Would you share Bits, feeds and speeds?

    I shared some some power valve guides here.

    I also made a boat console out of extruded PVC to replace a rotted wooden one on my...
  24. Thread: Tiki Totem

    by khaos
    Replies
    2
    Views
    2,550

    Is it possible that I never responded AT ALL to...

    Is it possible that I never responded AT ALL to this? So sorry. Thank you for the leads.
  25. Thread: World Map

    by khaos
    Replies
    3
    Views
    1,044

    Really cool. Thanks for sharing the details.

    Really cool. Thanks for sharing the details.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4