Page 3 of 16 FirstFirst 1234513 ... LastLast
Results 21 to 30 of 160

Thread: VCarved buttons

  1. #21
    Join Date
    May 2005
    Location
    Londonderry New Hampshire
    Posts
    341

    Default

    I don't care what they say - you CAN teach an OLD dog new tricks!
    Dick
    Aspire 10.5

  2. #22
    Join Date
    Jun 2013
    Location
    Pasadena, CA
    Posts
    986

    Default

    Buttons look great! I still have some 1/10" plywood left over that I laminated from different color veneer for another project. I may give that a try for buttons.

    I have not had much success for holding down small pieces (except for tabs). Thanks for all the tips here! I did try double sided high tack 3M foam tape one time and is was a big mess. The router bit ripped up the tape an slung adhesive boogers all over the shop.

  3. #23
    Join Date
    Jan 2004
    Location
    iBILD Solutions - Southern NJ
    Posts
    7,986

    Default

    High Definition 3D Laser Scanning Services - Advanced ShopBot CNC Training and Consultation - Vectric Custom Video Training IBILD.com

  4. #24
    Join Date
    Apr 2013
    Location
    Kennebunkport, Maine
    Posts
    4,419

    Default

    Brady, Thought you recommended Ace Hardware cloth reinforced carpet tape(that's what I bought and haven't used yet). Thanks for the help on this-
    scott P.
    2013 Desktop/spindle/VCP 11.5**
    Maine

  5. #25
    Join Date
    Jan 2004
    Location
    iBILD Solutions - Southern NJ
    Posts
    7,986

    Default

    I wrote that long ago...Yes - I've found Ace to be the best for our application. It must specifically say either "Fiberglass" or "Cloth" on the front of the box.

    Can't find it on their site now...I hope that isn't a sign.

    -B
    High Definition 3D Laser Scanning Services - Advanced ShopBot CNC Training and Consultation - Vectric Custom Video Training IBILD.com

  6. #26
    Join Date
    Apr 2013
    Location
    Kennebunkport, Maine
    Posts
    4,419

    Default

    Bought 3 weeks ago,
    Ace carpet tape
    cloth
    heavy duty
    #54308
    That the stuff?
    scott P.
    2013 Desktop/spindle/VCP 11.5**
    Maine

  7. #27
    Join Date
    Oct 2010
    Location
    TX
    Posts
    803

    Default

    "DUCK" brand works well. They have medium sized rolls at Wally-world. I buy it from a distributor in NJ in LARGE rolls and a couple cases at a time.

  8. #28
    Join Date
    Jan 2004
    Location
    iBILD Solutions - Southern NJ
    Posts
    7,986

    Default

    Yes- that's the stuff. The the one that says 'Fiberglass' on front is even better than the one that says 'cloth'.

    Monty - Yes the Duck stuff is good. I was using this until Depot stopped carrying it in my neck of the woods and replaced it with the mostly clear & 'snotty' stuff with like 3-5 tracer strings running through it. THAT stuff is NO good for CNC since you can't get the residue off the table! (Unless you scrape, douse with solvent, heat or machine it off)

    -B
    High Definition 3D Laser Scanning Services - Advanced ShopBot CNC Training and Consultation - Vectric Custom Video Training IBILD.com

  9. #29
    Join Date
    Oct 2010
    Location
    TX
    Posts
    803

    Default

    Brady: EXACTLY!! I hate their new stuff! I wish I could get them to carry the DUCK brand again! It's pretty good stuff! But a big kings x on the snotty stuff

  10. #30
    Join Date
    Jan 2004
    Location
    iBILD Solutions - Southern NJ
    Posts
    7,986

    Default

    Who's your source in NJ for Duck?

    -B
    High Definition 3D Laser Scanning Services - Advanced ShopBot CNC Training and Consultation - Vectric Custom Video Training IBILD.com

Similar Threads

  1. NOT buttons
    By scottp55 in forum Folder 2015
    Replies: 25
    Last Post: 01-02-2016, 06:23 AM
  2. 3D Buttons :)
    By scottp55 in forum Folder 2015
    Replies: 16
    Last Post: 07-24-2015, 07:12 AM
  3. 3.8.6 Buttons
    By Keyco Wood in forum ShopBotter Message Board
    Replies: 0
    Last Post: 06-15-2013, 01:47 PM
  4. Vcarved Plate from Partworks in Cherry.
    By pfulghum in forum Folder 2008
    Replies: 0
    Last Post: 10-12-2008, 11:47 PM
  5. Filling vcarved letters
    By alister in forum Archives2008
    Replies: 20
    Last Post: 09-07-2008, 01:54 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •