Just in time to order and get the 2016 tax break. Custom Control replacement systems for PR & PRT standard (PC chassis style) models.
https://youtu.be/W1Cw5W-51j4
For more info email: GCnC411@gmail.com
Just in time to order and get the 2016 tax break. Custom Control replacement systems for PR & PRT standard (PC chassis style) models.
https://youtu.be/W1Cw5W-51j4
For more info email: GCnC411@gmail.com
Gary Campbell
GCnC Control
GCnC411(at)gmail(dot)com
Servo Controller Upgrades
http://www.youtube.com/user/Islaww1
"We can not solve our problems with the same level of thinking that created them"
— Albert Einstein
How much do these run?
Tom Bachman,
Drafting/Woodworking Instructor RETIRED!
Lakin, Kansas
2001 PRT4896
https://i.imgur.com/xWEFfDk.jpg
Tom...
Specs and option pricing is in the attached pdf file
Gary Campbell
GCnC Control
GCnC411(at)gmail(dot)com
Servo Controller Upgrades
http://www.youtube.com/user/Islaww1
"We can not solve our problems with the same level of thinking that created them"
— Albert Einstein
To clarify a couple of email questions about the NEMA23 belt reduction units:
Can be seen in motion here: https://youtu.be/7AAq8SpJT-w at a minute, 16 seconds into the video.
Note: This is a previous version that did not use the ShopBot RBK I/O board that is no longer produced. Many of the components and for sure the belt reduction units are the same. The I/O board has been upgraded to the RBK version to enable added function and safety features.
Gary Campbell
GCnC Control
GCnC411(at)gmail(dot)com
Servo Controller Upgrades
http://www.youtube.com/user/Islaww1
"We can not solve our problems with the same level of thinking that created them"
— Albert Einstein
I am now happy to announce that due to volume and favorable purchasing agreements with suppliers that the base price for the REZurrection Control System has been lowered by $100 to $1695. Option pricing unchanged.
We also are now able to provide new, latest model ShopBot Controller cards with these systems should you desire one. Customers that order a new controller card with their system will receive a $100 discount on the assembled and tested system
Customers that have an old controller card to turn in will receive an additional $100 credit for it.
Gary Campbell
GCnC Control
GCnC411(at)gmail(dot)com
Servo Controller Upgrades
http://www.youtube.com/user/Islaww1
"We can not solve our problems with the same level of thinking that created them"
— Albert Einstein
To clarify a number of emails, that if you have any one of the PC chassis based systems, the basic REZurrection system replaces it and retains all original function. There will also be additional functions (from the RBK I/O board): more inputs and outputs (up to 12) and control for 2 spindles and/or routers. Spindle control logic (on/off) is built in. If you wish to have router control (on/off) the router contactor is required.
None of the other options are required unless you wish to add additional features.
Gary Campbell
GCnC Control
GCnC411(at)gmail(dot)com
Servo Controller Upgrades
http://www.youtube.com/user/Islaww1
"We can not solve our problems with the same level of thinking that created them"
— Albert Einstein
I am adding a belt drive product for PRS standard models to the REZurrection line. This will allow pre RBK PRS standard users to take advantage of the features of ShopBot's newest safety features and control enhancements by our utilization of the RBK I/O board and its compatibility with the latest generations of SB controller cards.
This system will also allow use of more modern digital drives and motors resulting in a substantial increase in cutting speeds, rapids and cut quality over the 4G.
This is a perfect upgrade for those that have put a lot of miles on the old gearboxes during frequent use, or have had a production requirement that is higher than when the machine was purchased.
For NEMA 23 nongeared motors (3/8 shaft): $325 ea with 350 ozin motor: $400
For NEMA 23 nongeared motors (3/8 shaft): $325 ea with 500 ozin motor: $420
For NEMA 34 nongeared motors (1/2 Shaft): $350 ea with 600 ozin motor: $450
Other combinations, including custom configurations, are available.
For more info contact: GCnC411@gmail.com
Gary Campbell
GCnC Control
GCnC411(at)gmail(dot)com
Servo Controller Upgrades
http://www.youtube.com/user/Islaww1
"We can not solve our problems with the same level of thinking that created them"
— Albert Einstein
An omission from the previous post: When purchased with a matching control system, deduct $50 each ($200 total for set of 4) from any of the above belt drive prices.
Gary Campbell
GCnC Control
GCnC411(at)gmail(dot)com
Servo Controller Upgrades
http://www.youtube.com/user/Islaww1
"We can not solve our problems with the same level of thinking that created them"
— Albert Einstein
As a current owner of these belt boxes and motors I can say that it's an excellent upgrade.