and ....... it wasn't Vectric's fault at all.......
Vectric's is at the top of the game for CNC software and provides great support. Been using their products for several years with ZERO issues.
and ....... it wasn't Vectric's fault at all.......
Vectric's is at the top of the game for CNC software and provides great support. Been using their products for several years with ZERO issues.
Jim
96 x 60 PRSalpha, 5HP Colombo spindle, Custom indexer, Custom vacuum table, Custom Fire Extinguishing System
ALSO.....I have to say that is TOTALLY unlike Dianne!!
She pulled our chestnuts out of the fire more than once by her prompt action and attention to detail on our 2 machines in different locations!
First time I've EVER heard a bad interaction with her!
Also Frank who took her place when she retired, was a GREAT person as well!!
Usually only "Above and Beyond" stories from Sales.
OP must have been an Outlier
Just couldn't keep quiet with my 2 cents.
scott
scott P.
2013 Desktop/spindle/VCP 11.5**
Maine
It was confirmed by Buddy Warner, that yes, Dianne collected money and never followed through. Buddy has graciously attempted to contact Vectric sales and they still refuse to register my software in my name. I am not going to beg for something I paid for. Finished with Vectric.
Hello Richard,
This Is Mark from Vectric support.
I believe that you may have misread or misinterpreted our response to you.
What we asked you to send to us was the original email that ShopBot had sent to you, that contained your license details.
You replied that you had previously sent your license details, but as was mentioned in our reply,
i am afraid that those details were only partial details.
I would guess that Dianne may have transferred your license and sent you some new license details,
but that those details may not have been entered into your software.
I replied to you again earlier this morning, as I mentioned in that reply, if you could please supply the information
requested, we will be able to register your software for you.
I hope that this helps.
Cheers,
Mark.
As previously stated in both this forum and to you, sir, Dianne did not send me an email, she sent me a receipt for my payment...hard copy. That copy has no information about registration.
Here is proof, check out the date. Of course the software will still show the original owner's name, Dianne didn't follow up with an email, that was confirmed by Shopbot support. Your blatant unwillingness to accept these simple facts is astonishing.
Richard,
I suggest you do the following:
1. Drop the attitude. It's absolutely sabotaging your ability to get a simple thing done.
2. Start cooperating. Both Vectric and Diane are willing and able to help you if you just do what you're asked.
3. Think before firing off an inflammatory post. It really doesn't help to come off as an ignorant lout.
4. Read with understanding. No doubt this is entirely your fault.
So step back, relax, take a few deep breaths and start from the beginning. Call Diane on the phone and have a pleasant conversation. A couple of minutes of intelligent discussion will get this solve. This isn't rocket science. It's simple and done everyday.
ShopBot Details:
2013 PRS 96x60x12 (Centroid upgrade)
4hp Spindle
12" indexer
Aspire
Rhino
Fusion 360
Ferrari 360
Prusa MK3S+
Prusa XL multi-tool
1. This has been ongoing for 8 years.
2. I cooperated for 8 years.
3. I have thought about it for 8 years.
4. I have read with understanding for 8 years, apparently you haven't.
From what I understand Dianne has retired. I have been talking with Buddy Warner, a representative of Shopbot. He has been attempting to help me.
You would understand all this if you had read the post from the beginning and not decided to troll this conversation and act 'like an ignorant lout'.
You may help by not making a judgement call on something you have no understanding about or ability to solve.
Well, I suggest you stick with your "Done with Vectric" attitude and see just how far that gets you. Good luck pal. You're going to need it.
ShopBot Details:
2013 PRS 96x60x12 (Centroid upgrade)
4hp Spindle
12" indexer
Aspire
Rhino
Fusion 360
Ferrari 360
Prusa MK3S+
Prusa XL multi-tool
Hello Richard,
It is not a problem if you do not have an email from ShopBot
if you could please supply the information that I requested in my reply to your last email, we will be able to register your software for you.
I hope that this helps.