Let's Talk ShopBot  

Go Back   Let's Talk ShopBot > General > Project Ideas

Reply
 
Thread Tools Display Modes
  #41  
Old 04-02-2012, 12:01 AM
Dan Hammerstron danhamm is offline
Senior Member
 
Join Date: Jun 2000
Location: 150 Mile House B.C. Canada
Posts: 471
Default

its totally a new table with a base and kind book space in between... and just for you jack..enjoy...

http://www.youtube.com/watch?v=cJ_Jd...=youtube_gdata
Attached Thumbnails
Click image for larger version

Name:	bktables 002.jpg
Views:	281
Size:	243.2 KB
ID:	14853  
Reply With Quote
  #42  
Old 04-02-2012, 07:51 AM
myxpykalix's Avatar
jack jarvis myxpykalix is offline
Senior Member
 
Join Date: Mar 2006
Posts: 7,160
Default

I'm beginning to think you take my "suggestions" as "challenges" and come up with something cooler then the previous one each time.
I liked the spinning top video but what you should do is carve the face of a roulette wheel or like the "wheel of fortune" and have it spin...

I had bought a "lazy susan" ball bearing wheel and it sounds kind of like thats what you had under your table? How did you mount that?
ANOTHER good project! You should start selling those tables like at craft shows and such.

I don't remember if i asked previously but what are you cutting them out of..plywood, glued up boards? How do your two different levels mount together?
Reply With Quote
  #43  
Old 04-12-2012, 01:57 PM
Dan Hammerstron danhamm is offline
Senior Member
 
Join Date: Jun 2000
Location: 150 Mile House B.C. Canada
Posts: 471
Talking

I would think a roulette wheel would have better bearings in it..was going to make a aztec roulette wheel...that would fall apart in december..lol
all the tables are made from laminated pine..or denim pine as they like to call it...bugkilled pine...
I dont go to - or sell at craft fairs...not my thing...I have a spot in Winsor Plywoods stores..and online..the small step table has doweling 1/2 inch pins in it. am still waiting for you to post your go at it..
Reply With Quote
  #44  
Old 04-13-2012, 12:41 PM
Phillip Bell pwbell is offline
New Member
 
Join Date: May 2007
Location: Grandpa's Sign and Millwork, Urbana ILLINOIS
Posts: 8
Default Please send files

Would you please send me the files?
Thank you.
Reply With Quote
  #45  
Old 04-13-2012, 03:33 PM
Bruce Dillingham orgtech is offline
New Member
 
Join Date: Mar 2010
Location: , McDonough GA
Posts: 11
Default

Could I please get a copy of your files. Thanks
__________________
Bruce
Desktop with spindle, indexer, Aspire
Trotec Speedy 300 80W
AirWolf AW3D HD2x Printer
Reply With Quote
  #46  
Old 04-14-2012, 01:42 AM
Dan Hammerstron danhamm is offline
Senior Member
 
Join Date: Jun 2000
Location: 150 Mile House B.C. Canada
Posts: 471
Default

need a address to send to.???
Reply With Quote
  #47  
Old 04-17-2012, 02:01 PM
Dan Hammerstron danhamm is offline
Senior Member
 
Join Date: Jun 2000
Location: 150 Mile House B.C. Canada
Posts: 471
Default

Its done.... wont send anymore...
Reply With Quote
  #48  
Old 04-21-2012, 01:34 AM
Dan Hammerstron danhamm is offline
Senior Member
 
Join Date: Jun 2000
Location: 150 Mile House B.C. Canada
Posts: 471
Default

Desk/table..entry..whatever...a little bigger same design...they are going over very well...
Attached Thumbnails
Click image for larger version

Name:	desk 006.jpg
Views:	291
Size:	242.3 KB
ID:	15116  
Reply With Quote
  #49  
Old 04-21-2012, 06:01 AM
myxpykalix's Avatar
jack jarvis myxpykalix is offline
Senior Member
 
Join Date: Mar 2006
Posts: 7,160
Default

Dan,
This looks taller then your last one, i think that was more coffee table height? I liked that one and this looks like just a taller version of the same. I like it very much too!
You need to start embellishing the tops of these tables although that might be overdoing it. Regardless you have a good thing going there buddy!
Reply With Quote
  #50  
Old 04-21-2012, 11:22 AM
Khalid Khattak khalid is offline
Senior Member
 
Join Date: Nov 2008
Posts: 650
Default

Quote:
Originally Posted by myxpykalix View Post
Dan,
I liked that one and this looks like just a taller version of the same. I like it very much too!
Hi Jack, When we like something we praise and we also want to make the same. These days on talkshopbot forum we have collected good amount of chairs dxf file from the kind guy ANDREW...

Jack, would you like DAN share this design with us?
__________________
I left woodwork due to office work.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:59 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright © 1999 - 2012 ShopBot® Tools, Inc.