- Offset distance for puzzle-like pieces? (6 replies)
- Feed speed (2 replies)
- Extira Vs. Medex (17 replies)
- Feed and speeds (2 replies)
- Vacuum Gasketing (4 replies)
- Laminating Extira? (27 replies)
- Cutting non-machinable materials; i.e. soft foam (3 replies)
- Bottom "chipping" in pocketing HDU... (4 replies)
- Dust Skirt and bit life (18 replies)
- Using 2 or more tools (17 replies)
- Hold down jig (7 replies)
- Feeds and Speeds (5 replies)
- New bleeder board (4 replies)
- Acrylics Again! (3 replies)
- Experimenting to find correct feed and speed (16 replies)
- Cutting smooth curves (7 replies)
- Machining Ipe (17 replies)
- Feed & speeds with large bits (5 replies)
- Router Judder (4 replies)
- Arranging cuts on sheet goods (8 replies)
- Tabbing (2 replies)
- Drilling holes in heart shape (10 replies)
- Baltic Birch revisited (0 replies)
- Part Wizard toolpath algorithm (3 replies)
- Help with cutting (8 replies)
- Stopping and starting extra long programs (6 replies)
- Rayite 100 (0 replies)
- Compression and downcut bits (10 replies)
- How do you get smooth cuts with the Alpha? (10 replies)
- Scaling At Run-Time (4 replies)
- VM Toolpath (4 replies)
- Long Shank Bits for Soft Foam (3 replies)
- Tools, feeds & speeds (3 replies)
- Cutting Carbon Kevlar hybrid (6 replies)
- Drilling into 2 3/4" MDF (0 replies)
- Clearance on mortises and tennons? (6 replies)
- Image test (14 replies)
- Starting values for the PRTalpha (15 replies)
- Cedar (8 replies)
- Need Modified Z Zero file (13 replies)
- Extira anyone? (8 replies)
- Phenolic Routing (3 replies)
- Cutting raised letters - reverse V-carve (3 replies)
- Cutting out letters , around the outside of the letter. (10 replies)
- Milling Type 1 Grey PVC (6 replies)
- 1" Roundover Bit (14 replies)
- Engraving 26 gauge copper (12 replies)
- FreeMill (0 replies)
- Cutting multiple parts from stacks of laminate (5 replies)
- Carving thermofoil (0 replies)
- RPM and Chipload Calculator (36 replies)
- HP rating for the PC-7518 motor (12 replies)
- Which size machine? (4 replies)
- 1/8" CED bit 3/4" long (1 replies)
- Trupan Ultralite MDF (37 replies)
- Ramped Entry with Vector (6 replies)
- Help - Ramp Speed Crisis (18 replies)
- Vertical accuracy? (1 replies)
- Need 1/4" Aluminum cut - Dallas, TX (0 replies)
- Holy Molly Static lit me up!! (4 replies)
- Collet inserts (28 replies)
- Looking for help with raised panels on Shopbot (1 replies)
- Hold down tape (3 replies)
- Choppy Machine tool path (4 replies)
- Cutting Depth / Clean up pass (15 replies)
- V' grooving (7 replies)
- Room Operating Conditions (10 replies)
- Cutting speed and depth in MDF (9 replies)
- Questions about cutters and speeds (5 replies)
- Timing butterfly pattern (7 replies)
- Cutters, speeds for baltic birch (9 replies)
- Mould making using resin casting (15 replies)
- Checking for square (2 replies)
- Propeller challenge (8 replies)
- MILLING PHENOLIC RESIN (10 replies)
- Cutting Plexiglass (17 replies)
- Sanding Reliefs (6 replies)
- Anybody using their ShopBot like a vinyl cutter? (19 replies)
- Geometry wizzards - pyramid problem for ya (10 replies)
- V Carve Router Bits (10 replies)
- What type of bit is best? (25 replies)
- Pneumatic Routers for Shopbot (84 replies)
- Accuracy again?? (13 replies)
- Cutting polyethelyene (4 replies)
- Ideal spindle speed vs. feed rate (12 replies)
- MDF cutting (54 replies)
- Cutting aluminum sheets (19 replies)
- Changing bits while cutting a Part File (8 replies)