- Zeroing question (6 replies)
- Mirtered Lightbox corner question. (4 replies)
- Proper Bit and speed for cutting HDPE (5 replies)
- Feed Rates for cutting PVC (4 replies)
- Number of Flutes in calculation (3 replies)
- Do you cut in stone? (1 replies)
- Dimension (1 replies)
- Really thick transfer tape (3 replies)
- Tapered End Mills (3 replies)
- Scalloped (7 replies)
- Engine Turning Surfacing Technique (Jewelling) (15 replies)
- Cutting Holes in Aluminum (6 replies)
- Cutting angles (11 replies)
- Cutting up and down and all over a sloped area (1 replies)
- Best bit? (3 replies)
- Z axis (3 replies)
- Square corners (7 replies)
- Help, I forgot the tool diameter used! (1 replies)
- Cutting Slate (6 replies)
- Has anyone ever cut HDO (11 replies)
- Using V Carve to check the angle of a V Bit (0 replies)
- Half and quarter round window trim (9 replies)
- Re-starting a file (14 replies)
- Router speed/noise (9 replies)
- Material for Casting Light Metals? (3 replies)
- Gator foam clean edge cuts question (19 replies)
- How to cutt 3/4 Baltic Birch wit a 3/8 compretion cutter (7 replies)
- Software for cuting a 45 deg. RPD (1 replies)
- Machining Elk Buttons (6 replies)
- Sintra / Komatex cutting help (9 replies)
- Router speed (2 replies)
- Trupan supplier in Great Northwest (8 replies)
- Vbit specs (8 replies)
- Safest High RPM's (3 replies)
- So how am I doing with this bit? (9 replies)
- Soap mold making (1 replies)
- Optimizing production files, ramping etc... (17 replies)
- Tips on V-carving metal... (5 replies)
- My vac setup. (4 replies)
- Really bent wood (0 replies)
- Workbench idea (1 replies)
- Dado's for a Newb (2 replies)
- Seriously large cutters (2 replies)
- Certainteed pvc trim board (11 replies)
- Old dogs and new tricks (48 replies)
- Hold down/fixture/cutting help (10 replies)
- Sandstone (10 replies)
- Screen door (2 replies)
- Not enough room to cut now my puck is done! (9 replies)
- Designing and cutting cab parts (0 replies)
- Cutting small parts in 1/2" Veneered MDF... (3 replies)
- Cutting Plexiglass (12 replies)
- ShopBot Logo (2 replies)
- How to compensate for variations in material thickness? (7 replies)
- Another Extruder question (2 replies)
- Question about cutting two materials (5 replies)
- Best method for cutting sintra (4 replies)
- Alupanel anyone? (15 replies)
- Query - Setting up 2 sided, angled work (1 replies)
- Extruder (3 replies)
- Cutters (3 replies)
- Making Beaded Panel Doors (2 replies)
- Biscuit Slots (6 replies)
- How to make a simple hot wire for eps foam for surfboards (6 replies)
- Surface Milling MDF (6 replies)
- PhotoVCarve question (27 replies)
- Not sure im getting the best cut? (8 replies)
- MDF &13 PLY BIT LIFE ? (2 replies)
- .ptn files (4 replies)
- Another Newbie Question (1 replies)
- Sliceing A model to fit under the gantry? (17 replies)
- Odd diameter errors in using CNC with lathe/indexer (3 replies)
- Bit size and type (2 replies)
- Feed speed for cutting mdf (8 replies)
- What are good bits to use when v-carving Aluminum and Brass? (3 replies)
- 4G Upgrade + laundry detergent = better aluminum cutting! (1 replies)
- CASTING ACRYLIC (11 replies)
- Planing a table top with the bot (7 replies)
- Help for drilling speed (3 replies)
- Milwaukie router speeds (2 replies)
- The PRS Wiggle (4 replies)
- Zeroing a hold down fixture to the table? (2 replies)
- Cutting speeds (5 replies)
- How to mill these on the bot? (13 replies)
- Challenge (13 replies)
- Trig problem, probably (4 replies)
- NEED HELP !!! How do I cut solid surface countertops??? (11 replies)
- Turning a tapered column (30 replies)
- Drawer Boxes (2 replies)
- Perhaps a bit OT - Cutting Mudflaps (12 replies)
- 3D Digitizing Probe (11 replies)
- Has anyone used a 3/8" collet with Milwaukee 5625 router? (16 replies)
- Need some help (2 replies)
- Need help reducing chatter lines in acrylic (16 replies)
- Suggestions for Cutting, spacking, and gluing wooden hoops? (8 replies)
- Swapped to a 1/2" bit, and everything went wrong... why? (6 replies)
- Carve half now - other half tomorrow (15 replies)
- The Shopbot Camp made me do it…. (2 replies)
- How fast is too fast on Z for drilling... (2 replies)
- Edge finding, 2 D replication (2 replies)
- Need input on Carving Banjo Necks: Initial Design & Tweaks (1 replies)
- Hold down for board blank... (22 replies)
- Surfboards (24 replies)
- Releif carving bit sizes (6 replies)
- 'Roo Glue and edge banding (12 replies)