View Full Version : Custom Dust Shoe Size?
I think I am going to have to make my own dust shoe to allow the foot and hose to fit between the two Y rails on my old SB. I want the foot to be adjustable but fixed as opposed to being attached to the router.
Is there any advantages to having the dust foot larger or smaller?
Where can I get the rare earth magnets and the flexible brush material?
Any tips on the mounting, hose, the up down and locking mechanism etc?
steve_g
05-31-2017, 02:57 AM
https://www.kjmagnetics.com/
http://www.brush.com/type/tstrip.html
https://www.gordonbrush.com/strip_brushes.php
https://www.kjmagnetics.com/
http://www.brush.com/type/tstrip.html
https://www.gordonbrush.com/strip_brushes.php
Thanks. I found this one from an old thread.
https://www.sealeze.com/products/xtraseal-strip-brush
Anyone know which one is like the Kent brush? I read he doubles up on the strip. Is that correct? (note I own a Kent shoe but I need to make a custom one now.)
knight_toolworks
05-31-2017, 11:21 PM
I can give you the plans my new design. though it is mounted on my new prs Z but you can adapt it. you need to stick to 3" hose 4" just gets in the way. he uses a single brush and you can buy them from him myself I like the horsehair ones.
I can give you the plans my new design. though it is mounted on my new prs Z but you can adapt it. you need to stick to 3" hose 4" just gets in the way. he uses a single brush and you can buy them from him myself I like the horsehair ones.
yes please. If you want to email it to me, rib9080 (at) gmail (dot) com
knight_toolworks
05-31-2017, 11:35 PM
yes please. If you want to email it to me, rib9080 (at) gmail (dot) com
Ok here are the pics
http://www.talkshopbot.com/forum/attachment.php?attachmentid=30295&stc=1
http://www.talkshopbot.com/forum/attachment.php?attachmentid=30296&stc=1http://www.talkshopbot.com/forum/attachment.php?attachmentid=30297&stc=1
Thanks for the pics. Hold off on the files for now, I will have to see if there is enough room on my machine for this. Looks great. Is there any disadvantage to having it attached at the back of the Z like that?
knight_toolworks
06-01-2017, 12:36 AM
Thanks for the pics. Hold off on the files for now, I will have to see if there is enough room on my machine for this. Looks great. Is there any disadvantage to having it attached at the back of the Z like that?
it should fit it may need to be shortened by 1/2" Had a little extra room when I went with the new z. give me the measurement from the spindle to the bar. the 3: hose is what makes it work. it is better being attached Icahn change the height it makes w world of difference on how it works so much better.
phil_o
06-01-2017, 06:39 AM
I made a dust shoe similar to this. https://www.youtube.com/watch?v=ufXTIu2VmME&t=658s
A similar design https://www.youtube.com/watch?v=ufXTIu2VmME&t=658shttp://www.suckitdustboot.com/purchase
Phil
I made a dust shoe similar to this. https://www.youtube.com/watch?v=ufXTIu2VmME&t=658s
A similar design https://www.youtube.com/watch?v=ufXTIu2VmME&t=658shttp://www.suckitdustboot.com/purchase
Phil
Thank you for sharing these videos. I think am going to make a dust shoe that is independent of the router. That's the way I am used to working. Are there issues with the shoe attached to the router?
Powered by vBulletin® Version 4.2.2 Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.