Page 1 of 38 12311 ... LastLast
Threads 1 to 20 of 751

Forum: Techniques for Cutting, Drilling, Machining

Sub-Forums Threads / Posts  Last Post

  1. Forum Actions:

    Forum Statistics:

    • Threads: 735
    • Posts: 7,052

    Last Post:

    Best tool for trimming /... Go to last post

    by curtiss

    06-16-2015, 08:43 PM

  1. cutting 1.5" pucks

    Started by twelchPTM, 04-30-2021 08:56 AM
    • Replies: 3
    • Views: 593
    04-30-2021, 10:45 AM Go to last post
  2. Hold down for planing slabs

    Started by cradke0419, 02-25-2021 09:37 PM
    • Replies: 2
    • Views: 787
    02-26-2021, 10:11 AM Go to last post
  3. Polymer clay to make a negative

    Started by coryatjohn, 01-14-2021 06:45 PM
    • Replies: 0
    • Views: 692
    01-14-2021, 06:45 PM Go to last post
  4. Multi-sided machining Tips

    Started by tallen84, 12-29-2020 02:25 PM
    • Replies: 5
    • Views: 1,039
    01-10-2021, 11:23 AM Go to last post
  5. Machining wax

    Started by coryatjohn, 01-04-2021 09:24 AM
    • Replies: 0
    • Views: 580
    01-04-2021, 09:24 AM Go to last post
  6. Speeding Up 2.5D Carving on 60 lb. Foam

    Started by rgreever, 11-24-2020 01:22 PM
    • Replies: 3
    • Views: 1,047
    11-24-2020, 04:58 PM Go to last post
  7. Longer bit suggestions.

    Started by twelchPTM, 10-16-2020 03:22 AM
    • Replies: 1
    • Views: 962
    10-16-2020, 09:10 AM Go to last post
  8. Shopbot pauses before drilling hole

    Started by Zads, 08-14-2020 03:05 PM
    • Replies: 3
    • Views: 1,270
    08-15-2020, 10:47 AM Go to last post
  9. ShopBot Circles cuts out of alignment

    Started by CDarby67, 07-20-2020 08:17 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 2,791
    07-21-2020, 11:50 AM Go to last post
  10. V-carve - ridges left after cut

    Started by chein, 05-19-2020 01:04 PM
    • Replies: 4
    • Views: 1,496
    05-20-2020, 08:45 PM Go to last post
  11. Question Cut Parameter Recommendations

    Started by BasisPet, 04-05-2020 08:38 AM
    • Replies: 8
    • Views: 2,473
    04-06-2020, 11:43 AM Go to last post
  12. Part Larger then VCarve file

    Started by Rcornelson, 03-23-2020 01:04 PM
    • Replies: 2
    • Views: 1,075
    03-23-2020, 04:56 PM Go to last post
  13. Bit choice for a project

    Started by CDarby67, 02-28-2020 04:25 PM
    • Replies: 2
    • Views: 1,329
    02-29-2020, 05:04 PM Go to last post
  14. Using PVA as a mask

    Started by coryatjohn, 01-05-2020 08:43 PM
    • Replies: 4
    • Views: 2,175
    02-21-2020, 08:22 AM Go to last post
  15. Precise cutting of heavy brass tube

    Started by coryatjohn, 12-11-2019 12:56 PM
    • Replies: 4
    • Views: 2,027
    12-13-2019, 02:59 PM Go to last post
  16. Liquid Urethane Foam

    Started by coryatjohn, 11-26-2019 03:58 PM
    • Replies: 6
    • Views: 2,368
    11-28-2019, 11:05 AM Go to last post
    • Replies: 8
    • Views: 2,397
    11-19-2019, 11:38 PM Go to last post
  17. question on deep cutting

    Started by ddrumguy, 10-20-2019 08:34 AM
    • Replies: 4
    • Views: 2,474
    10-24-2019, 12:29 AM Go to last post
    • Replies: 7
    • Views: 2,987
    10-01-2019, 08:59 PM Go to last post
  18. 30° V-bit woes

    Started by blackhawk, 10-01-2019 01:48 PM
    • Replies: 0
    • Views: 1,296
    10-01-2019, 01:48 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •