Page 1 of 14 12311 ... LastLast
Threads 1 to 20 of 270

Forum: Assembly & Maintenance

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. Weight of a 4x8 PRT ShopBot

    Started by David Iannone, 02-29-2012 11:47 AM
    2 Pages •
    1 2
    6 Attachment(s)
    • Replies: 12
    • Views: 27,314
    jkaras2000
    03-08-2025, 01:17 PM Go to last post

  2. Z problem

    Started by dan78, 11-10-2024 02:33 AM
    2 Pages •
    1 2
    2 Attachment(s)
    • Replies: 10
    • Views: 6,199
    dan78
    11-28-2024, 02:50 PM Go to last post

  3. Squaring process sanity check...

    Started by geneb, 04-18-2024 08:11 PM
    • Replies: 5
    • Views: 14,435
    geneb
    04-25-2024, 09:26 AM Go to last post

  4. Looking for photos of PRT Alpha upgrade...

    Started by geneb, 04-24-2024 07:50 PM
    • Replies: 0
    • Views: 6,043
    geneb
    04-24-2024, 07:50 PM Go to last post

  5. what a day - table build suggestions?

    Started by ddrumguy, 10-27-2023 04:03 PM
    • Replies: 3
    • Views: 8,092
    coryatjohn
    10-29-2023, 12:22 PM Go to last post

  6. 2004 PRT alpha spindle wiring

    Started by sawkerf, 09-08-2023 09:54 PM
    • Replies: 0
    • Views: 6,773
    sawkerf
    09-08-2023, 09:54 PM Go to last post

  7. 2.2 hp spindle fan

    Started by tracys, 09-08-2023 05:41 PM
    • Replies: 0
    • Views: 6,697
    tracys
    09-08-2023, 05:41 PM Go to last post

  8. Question Control software for 3.8.76

    Started by Scott216, 07-13-2023 08:14 AM
    • Replies: 0
    • Views: 6,900
    Scott216
    07-13-2023, 08:14 AM Go to last post

  9. Disassembling PRS Alpha 120-60-6

    Started by anothernewbie, 04-12-2023 08:23 AM
    disassembly, prs alpha
    • Replies: 0
    • Views: 9,486
    anothernewbie
    04-12-2023, 08:23 AM Go to last post

  10. Drawbar did not open properly. ATC 269

    Started by andrius.ack, 09-07-2022 11:43 AM
    1 Attachment(s)
    • Replies: 4
    • Views: 12,027
    dlcw
    09-07-2022, 03:19 PM Go to last post

  11. Gantry wheel not touching guide

    Started by bbortnick, 08-11-2022 06:02 PM
    2 Pages •
    1 2
    • Replies: 10
    • Views: 14,476
    MogulTx
    08-21-2022, 06:28 PM Go to last post

  12. spindle movement, unround holes

    Started by bbortnick, 08-03-2022 06:13 PM
    2 Pages •
    1 2
    • Replies: 10
    • Views: 14,326
    bbortnick
    08-10-2022, 07:20 PM Go to last post

  13. Question Replacement key switch

    Started by Scott216, 07-28-2022 12:35 PM
    • Replies: 3
    • Views: 8,344
    coryatjohn
    07-30-2022, 10:51 AM Go to last post

  14. General vacuum question

    Started by ClayM325, 10-18-2021 10:06 AM
    • Replies: 2
    • Views: 10,168
    ClayM325
    10-18-2021, 02:20 PM Go to last post

  15. PRT Alpha 48x96 Holding Z axis mount vertical on X direction

    Started by AllisterMcRae, 10-08-2021 05:04 PM
    3 Attachment(s)
    • Replies: 3
    • Views: 8,494
    waynelocke
    10-16-2021, 03:29 PM Go to last post

  16. Desktop block bearings. Machine wouldn't move in the X axis.

    Started by Bud Meade, 09-05-2021 06:10 PM
    8 Attachment(s)
    • Replies: 7
    • Views: 11,069
    scottp55
    09-10-2021, 09:42 AM Go to last post

  17. PRS Vaccum Foot.....

    Started by Minuteman Graphics Fayetteville NC, 09-02-2021 02:47 PM
    • Replies: 0
    • Views: 7,827
    Minuteman Graphics Fayetteville NC
    09-02-2021, 02:47 PM Go to last post

  18. Delta VFD input multifunction program?

    Started by rsteven18, 06-10-2021 10:51 PM
    2 Attachment(s)
    • Replies: 0
    • Views: 9,106
    rsteven18
    06-10-2021, 10:51 PM Go to last post

  19. VFD & single phase input help

    Started by rsteven18, 04-25-2021 12:30 AM
    4 Attachment(s)
    • Replies: 7
    • Views: 11,274
    JMCS
    04-29-2021, 09:09 AM Go to last post

  20. tram lines

    Started by letterman7, 04-22-2021 08:46 AM
    1 Attachment(s)
    • Replies: 0
    • Views: 8,480
    letterman7
    04-22-2021, 08:46 AM Go to last post
Page 1 of 14 12311 ... LastLast

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules