Page 1 of 16 12311 ... LastLast
Threads 1 to 20 of 315

Forum: Variations & Modifications of ShopBots

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. Gecko Drivers for PRT 3.5 and earlier

    Started by pegheds, 09-03-2024 07:10 PM
    gecko, hack, prt
    • Replies: 2
    • Views: 2,793
    09-04-2024, 12:07 PM Go to last post
  2. Spindle Swap to Light Work Steel

    Started by verhoevc, 11-14-2023 10:37 PM
    2 Pages
    1 2
    • Replies: 11
    • Views: 14,764
    11-17-2023, 05:00 PM Go to last post
    • Replies: 0
    • Views: 4,137
    11-07-2023, 09:10 PM Go to last post
  3. 3rd party touch probe on PRS Alpha

    Started by Scott216, 06-23-2022 09:01 PM
    • Replies: 0
    • Views: 7,796
    06-23-2022, 09:01 PM Go to last post
  4. ShopBot Table expansion

    Started by MogulTx, 08-26-2021 09:19 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 17,893
    08-29-2021, 09:41 AM Go to last post
  5. Hi has any one done a downgrading on a prs alpha

    Started by JanBo, 06-07-2021 07:50 AM
    • Replies: 4
    • Views: 7,181
    06-08-2021, 03:16 AM Go to last post
  6. Looking for a Post Processor for vacuum pods.

    Started by andrius.ack, 11-11-2020 04:10 PM
    2 Pages
    1 2
    • Replies: 12
    • Views: 18,693
    04-25-2021, 07:03 PM Go to last post
  7. Plug and play 3d laser scanner?

    Started by cybertunerone, 12-18-2020 11:05 AM
    • Replies: 0
    • Views: 9,720
    12-18-2020, 11:05 AM Go to last post
  8. Plug and play 3d laser scanner?

    Started by cybertunerone, 12-17-2020 05:47 PM
    • Replies: 0
    • Views: 6,321
    12-17-2020, 05:47 PM Go to last post
  9. how to wire 4 lamb amatek 240v motors

    Started by Stuart Kent, 11-19-2020 10:22 AM
    • Replies: 0
    • Views: 7,413
    11-19-2020, 10:22 AM Go to last post
    • Replies: 14
    • Views: 35,865
    11-11-2020, 04:04 PM Go to last post
  10. Increase Power on Yaskawa 2.2hp VFD for Cheap

    Started by PaulWall, 10-31-2020 09:45 PM
    • Replies: 0
    • Views: 8,106
    10-31-2020, 09:45 PM Go to last post
    • Replies: 0
    • Views: 8,587
    09-14-2020, 05:18 PM Go to last post
  11. New spindle, control question

    Started by mercuru049, 08-11-2020 03:44 PM
    • Replies: 1
    • Views: 7,664
    08-11-2020, 06:21 PM Go to last post
  12. FabMo & Raspberry Pi on a V4g control board

    Started by Jimmy Walker, 04-07-2020 02:17 PM
    • Replies: 1
    • Views: 13,113
    04-07-2020, 03:06 PM Go to last post
  13. Anyone installed a spindle at an angle?

    Started by chris_booth, 02-12-2020 07:38 AM
    2 Pages
    1 2
    • Replies: 15
    • Views: 20,775
    02-14-2020, 01:09 PM Go to last post
  14. Aftermarket Relay For Extra Output Controls

    Started by NicholasB, 04-23-2018 01:22 PM
    • Replies: 1
    • Views: 24,151
    09-12-2019, 06:11 PM Go to last post
  15. 3D printed dust shoe

    Started by EricSchimel, 08-28-2019 11:18 AM
    • Replies: 2
    • Views: 13,609
    08-28-2019, 12:59 PM Go to last post
  16. Welding my X gantry (Part 1 of 3)

    Started by Chuck Keysor, 06-26-2019 03:58 AM
    2 Pages
    1 2
    • Replies: 10
    • Views: 32,365
    06-29-2019, 01:46 AM Go to last post
    • Replies: 3
    • Views: 19,956
    05-11-2019, 06:35 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •