Page 11 of 38 FirstFirst ... 91011121321 ... LastLast
Threads 201 to 220 of 744

Forum: Troubleshooting

Email support@shopbottools.com or call us if you have an urgent problem.

Sub-Forums Threads / Posts  Last Post

  1. Archives Threads / Posts  Last Post

  1. BEWARE!!! Version 3.8.30

    Started by PNast, 05-14-2015 04:26 PM
    2 Pages
    1 2
    • Replies: 19
    • Views: 12,143
    05-24-2015, 09:46 PM Go to last post
  2. Sorting things out…

    Started by brianwiley, 05-20-2015 08:59 PM
    • Replies: 5
    • Views: 5,714
    05-22-2015, 07:07 PM Go to last post
  3. Exclamation Vacuum Blower Over-heating issues

    Started by JNathan09, 05-21-2015 07:10 PM
    • Replies: 2
    • Views: 6,050
    05-22-2015, 11:02 AM Go to last post
  4. Question ShopBot not cutting accurately!

    Started by MitchTalmadge, 05-19-2015 02:42 AM
    2 Pages
    1 2
    • Replies: 14
    • Views: 12,922
    05-22-2015, 10:39 AM Go to last post
  5. toolpath

    Started by hknisely, 05-19-2015 12:14 PM
    • Replies: 2
    • Views: 2,488
    05-19-2015, 08:35 PM Go to last post
  6. Strange new problem

    Started by tlempicke, 05-17-2015 05:25 PM
    2 Pages
    1 2
    • Replies: 13
    • Views: 8,601
    05-19-2015, 07:30 PM Go to last post
  7. Variation in Calibration (X & Y)

    Started by gregg, 05-18-2015 05:10 PM
    • Replies: 4
    • Views: 3,789
    05-18-2015, 07:32 PM Go to last post
  8. Question Unit Values for Z and A are not the same

    Started by SparksStudios, 05-09-2015 06:31 PM
    • Replies: 3
    • Views: 3,539
    05-12-2015, 09:53 AM Go to last post
  9. Runtime error 6 overflow- resolved in Icelandic

    Started by willnewton, 04-28-2015 12:04 AM
    • Replies: 2
    • Views: 3,367
    05-12-2015, 01:14 AM Go to last post
  10. USB not conectting

    Started by Almost Scientific, 10-22-2012 06:35 PM
    • Replies: 3
    • Views: 5,175
    05-04-2015, 07:02 PM Go to last post
  11. control over B axis

    Started by markevans, 05-02-2015 08:03 PM
    • Replies: 4
    • Views: 2,863
    05-04-2015, 12:21 AM Go to last post
  12. Vacuum Table Issues

    Started by ChrisR, 04-15-2015 12:16 PM
    • Replies: 6
    • Views: 5,193
    04-20-2015, 04:31 PM Go to last post
  13. Multipass Cut Through - Not Retracing in the same spot.

    Started by TNWALKINGHORSE, 03-31-2015 12:49 AM
    4 Pages
    1 2 3 ... 4
    • Replies: 30
    • Views: 37,022
    04-13-2015, 12:49 AM Go to last post
  14. Z axis zeroing and drifting deeper problems

    Started by bbobmc, 04-11-2015 03:48 PM
    • Replies: 6
    • Views: 7,374
    04-12-2015, 11:49 PM Go to last post
  15. Loss of Vacuum Hold Down

    Started by jdervin, 04-11-2015 03:49 PM
    • Replies: 5
    • Views: 3,254
    04-12-2015, 08:50 AM Go to last post
  16. X2 motor turns freely

    Started by asemcollc, 04-11-2015 03:10 PM
    stepper motors
    • Replies: 2
    • Views: 2,492
    04-12-2015, 07:59 AM Go to last post
  17. Keyboard move issues

    Started by wwaldner, 03-28-2015 11:35 AM
    2 Pages
    1 2
    keyboard freeze
    • Replies: 11
    • Views: 8,760
    04-01-2015, 05:41 PM Go to last post
  18. Hogging Out - Saving Time - then finish bit

    Started by TNWALKINGHORSE, 03-31-2015 10:49 PM
    • Replies: 2
    • Views: 3,264
    03-31-2015, 11:15 PM Go to last post
  19. Bot kept stopping during job

    Started by barrowj, 03-30-2015 10:57 AM
    • Replies: 5
    • Views: 4,176
    03-31-2015, 06:44 PM Go to last post
  20. z axis not responding

    Started by gene, 03-19-2015 01:56 AM
    • Replies: 9
    • Views: 10,790
    03-20-2015, 04:15 PM Go to last post

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 15 replies or 150 views
Hot thread with unread posts
More than 15 replies or 150 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •