Search:

Type: Posts; User: Gary Campbell

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    5
    Views
    946

    This may help

    This may help
  2. Replies
    14
    Views
    5,211

    Normally this is a built in feature of the...

    Normally this is a built in feature of the controller. Red = Alarm or prior to homing, Yellow = Idle, Green = executing (running) commands

    You will have to use a relay board and place the...
  3. Replies
    5
    Views
    1,082

    Another way to skin that cat: ...

    Another way to skin that cat: https://youtu.be/C7b7He0mtxk
  4. I have purchased, tested and returned a half...

    I have purchased, tested and returned a half dozen sets of eBay gearboxes. Most are junk as they have lots of backlash. You may find some that are better.

    The NEMA23 planetary's that Scott has...
  5. Paul... Good luck with your system. There are a...

    Paul...
    Good luck with your system. There are a lot of SB'ers on the Acorn forum that will assist you in the process.

    You may want to rethink the belt vs. planetary choice. I used to sell them,...
  6. Replies
    11
    Views
    2,637

    Loss of a friend

    It is with a sad heart that long time ShopBotter and forum contributor, Dave Rosenbleeth, has lost his battle with cancer.

    He fought a valiant fight for years, but in the end the disease won the...
  7. Replies
    8
    Views
    2,890

    Use a profile with spiral ramp, not a pocket

    Use a profile with spiral ramp, not a pocket
  8. Replies
    33
    Views
    9,060

    [QUOTE=8Ball;204903]This forum appears to have...

    [QUOTE=8Ball;204903]This forum appears to have lost momentum.
    This used to be a go-to place for information, but the activity has declined significantly.
    Are people moving away from this brand?...
  9. Replies
    51
    Views
    21,874

    Steve.. Why are you asking about a CAMaster...

    Steve..
    Why are you asking about a CAMaster PostP on the ShopBot forum without asking on the CAMaster forum first? As Gary B states, the Carveco posts are virtually as editable as Vectric's are....
  10. Replies
    0
    Views
    1,055

    SB Control Computer

    Not the complete computer, just all the parts that count. This is an ASUS AT5IONT-I Motherboard, with onboard Intel Atom (dual) processor, 4gb RAM, 256GB SSD, MOBO manual and driver install disc. ...
  11. Replies
    1
    Views
    1,711

    Michael Mezzalick does both basic and more...

    Michael Mezzalick does both basic and more advanced Aspire training on a regular basis at the new AXIOM HQ in Columbus, OH. Class size is designed to allow attention to virtually all user issues. ...
  12. Replies
    2
    Views
    2,087

    Select all Using the offset tool, offset in/out...

    Select all
    Using the offset tool, offset in/out one half the diameter change,
    select "delete original"
  13. Remove the line that is similar to "J2, [XH],...

    Remove the line that is similar to "J2, [XH], [YH]" from the NEW_SEGMENT section.
  14. Really??? With a bit of a tuneup even a PRS...

    Really??? With a bit of a tuneup even a PRS standard will fly: https://youtu.be/33gLcfC59pA
  15. John... Is this a recurring issue or a one off...

    John...
    Is this a recurring issue or a one off anomaly? If recurring, do you have a video or a set of actions to recreate? This does not seem to be something other than rare and has my curiosity...
  16. So.... John, Because the written word, without...

    So.... John,
    Because the written word, without tonal inflection can be easily misinterpreted, I need to ask: Since there appears to be differing opinions, which side would you believe to be more...
  17. Replies
    9
    Views
    2,110

    In reality, a prox on the Z will do as much if...

    In reality, a prox on the Z will do as much if not more that they do on the X & Y. I put one on my PRS in '08 and wouldn't have a machine without one.
  18. Replies
    1
    Views
    898

    Matthew... At one time there was a SB'er in...

    Matthew...
    At one time there was a SB'er in Houston using Microvellum and a couple (at least) SB machines. Don't know what he is doing now, but I remember hime "talking' about ~$5k for a SB postP. ...
  19. Replies
    9
    Views
    4,621

    Eric... Other than a few you may use for special...

    Eric...
    Other than a few you may use for special purposes like jig positioning or some "hipster stuff" (sorry, had to do that :) ) most any macro you would want is posted on the Acorn forum. If...
  20. Replies
    12
    Views
    6,448

    Explode the text prior to exporting from ACad

    Explode the text prior to exporting from ACad
  21. Replies
    12
    Views
    5,379

    Jeff... Let me add ".... without milling a...

    Jeff...
    Let me add ".... without milling a proper surface" to that. I would further say that there is no doubt of the increased capability of speed, cut quality and rigidity. But unless you plan...
  22. Replies
    12
    Views
    5,379

    +1 to what Brady says. Not interested. I would...

    +1 to what Brady says. Not interested. I would do it like they do and have a complete replacement, that due to lower volume, in all honesty would cost more than the SB product.

    Many of the...
  23. 32139 32140 https://youtu.be/zKzjhp-yDkE

    32139

    32140


    https://youtu.be/zKzjhp-yDkE
  24. Replies
    106
    Views
    24,932

    It appears to have been clearly stated: They are...

    It appears to have been clearly stated: They are not providing updates or support for the discounted Links. You don't have one. Unless I don't understand what your definition of support is,...
  25. Replies
    106
    Views
    24,932

    Start it up and use it just like you have every...

    Start it up and use it just like you have every time prior to today. They didn't say they were going to repossess them.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4