Search:

Type: Posts; User: evan

Page 1 of 9 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    2
    Views
    466

    Sounds like something is out of square. Check the...

    Sounds like something is out of square. Check the Gantry hasn't racked, isn't square to the rails. Also be sure the rails are dead parallel to each other. Drop the pinions off the racks, move the...
  2. Replies
    42
    Views
    8,741

    Thank you Scott, It's been trying times for...

    Thank you Scott,

    It's been trying times for sure! We've been playing it safe as well with a 92 , a 93 and a couple 80+ year olds not to mention the youngsters (all the way down to 7). Hopefully...
  3. Replies
    42
    Views
    8,741

    Lucky Liam! Those look great. I'm kinda partial...

    Lucky Liam! Those look great. I'm kinda partial to the first, the lighter one, not that it matters, ;-)
    Hope your Holidays are warm and you and yours are safe.
  4. Replies
    23
    Views
    3,073

    I like this idea, although if you should happen...

    I like this idea, although if you should happen to accidently send the bit through the spoil board (which I've never done... NOT LOL), there'd be hell to pay.
  5. Replies
    23
    Views
    3,073

    In 2005 /2006 I put in a 1.25" thick Paperstone...

    In 2005 /2006 I put in a 1.25" thick Paperstone bed. (I was cutting a lot of countertops at the time) If you are going to cut a vacuum grid into it (probably any phenolic top) you should keep in...
  6. Replies
    42
    Views
    8,741

    Looking Good!

    Looking Good!
  7. Replies
    9
    Views
    1,768

    https://www.mcmaster.com/oil-separators/ not...

    https://www.mcmaster.com/oil-separators/ not the only source just a place to start. It's recommended (and good for all air tools) to have one down the line (far enough away form the compressor so...
  8. Replies
    42
    Views
    8,741

    The bear is very indicative of the north west,...

    The bear is very indicative of the north west, captures it wonderfully, I'm sure you will do it justice, even though you're on the other coast ;-) I've done very little carving on the Shop Bot but...
  9. Replies
    42
    Views
    8,741

    Absolutely Beautiful! Exquisite detail! Looking...

    Absolutely Beautiful! Exquisite detail! Looking forward to seeing it in the soap stone. Thank you for sharing!
  10. Replies
    3
    Views
    1,094

    Don't think you need to remove the gantry but you...

    Don't think you need to remove the gantry but you will need to check for level and square after moving it. It doesn't take too much force to rack a bolted frame.
  11. Replies
    21
    Views
    7,496

    Vectric V10.5 Tutorials | Thread Milling Toolpath...

    Vectric V10.5 Tutorials | Thread Milling Toolpath Guide 2D Toolpaths https://www.youtube.com/watch?v=Ehb6KKyLdcI
  12. Thread: Dust Mask

    by evan
    Replies
    11
    Views
    1,435

    There are a lot of variables that go into Amazons...

    There are a lot of variables that go into Amazons pricing AI and none of it is transparent... or fair. But they are convenient.
  13. Replies
    17
    Views
    2,663

    knight-toolworks- With clear Gorrilla glue......

    knight-toolworks-

    With clear Gorrilla glue... used liquid nails once but decided it was over kill.:rolleyes:
  14. Replies
    17
    Views
    2,663

    Since I don't have strong enough vacuum (just a...

    Since I don't have strong enough vacuum (just a diy two motor "black box") I glue the MDF along edges and across the bed every 24". When it gets surfaced down to about 5/16" I glue new MDF on top. ...
  15. Replies
    17
    Views
    2,663

    If you're not to worried about cost and you'd...

    If you're not to worried about cost and you'd like to add some mass and stability to the table you might think about a material like Richlite or Paperstone. Little if any movement. Expanded PVC has...
  16. Replies
    17
    Views
    3,397

    Don't forget that these pinion gears often have...

    Don't forget that these pinion gears often have two set-screws in each threaded hole, one on top of the other.
  17. Should be able to find them in folder with in the...

    Should be able to find them in folder with in the ProgramData file:
    C:\ProgramData\Vectric\Aspire\V10.0\PostP\02-ShopBot
  18. Replies
    21
    Views
    5,462

    If you have the head room, while thinking of...

    If you have the head room, while thinking of ventilation you might consider a raised floor with dust collection coming from below, it can leave you with a much larger feeling shop.
  19. Thanks for the link!

    Thanks for the link!
  20. Replies
    24
    Views
    10,846

    Beautiful! Thanks for the post, it put a smile...

    Beautiful! Thanks for the post, it put a smile on my face.
  21. Great success cutting 3/4 PreFinished ApplyPly ...

    Great success cutting 3/4 PreFinished ApplyPly with AMANA #46180-K (K indicates ceramic coating) run @ 12k rpm, 2.5 - 3" per sec. (depending on part geometry), 5 passes.
  22. Try either: Aura Hardwoods 800.411.2872 or...

    Try either: Aura Hardwoods 800.411.2872 or Moore-Newton Quality Hardwoods 800.750.6009,
    Both deliver to Marin
  23. Replies
    50
    Views
    17,096

    Great to know thanks.

    Great to know thanks.
  24. Replies
    50
    Views
    17,096

    Not sure it's an issue but when drawing is in...

    Not sure it's an issue but when drawing is in metric, I use metric tooling, when generating the tool paths, and when the drawing is in imperial I use imperial tooling, when generating the tool paths.
  25. Replies
    17
    Views
    8,287

    Here on the Left coast there called sex bolts...

    Here on the Left coast there called sex bolts :D... Male and Female threads
Results 1 to 25 of 213
Page 1 of 9 1 2 3 4