Search:

Type: Posts; User: Scott216

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    105

    Good to know, thanks

    Good to know, thanks
  2. Replies
    3
    Views
    105

    I guess it could be the case SF, 0 only turns off...

    I guess it could be the case SF, 0 only turns off limit checking temporarily. Is that how it works from a sbc file?
  3. Replies
    3
    Views
    105

    Turn off software limits from sbc file

    I want to turn Software Limit checking off using this command:

    SF, 0

    I added it to a sbc file I use. But it has no effect. Is there a different command I should use in the sbc file to do...
  4. Replies
    3
    Views
    558

    Thanks, I'll give that a try. The values aren't...

    Thanks, I'll give that a try. The values aren't changing on their own (via corrupt file or something). The shopbot I use is at a Makerspace and I've noticed the my program my take 2x or more longer...
  5. Replies
    3
    Views
    558

    Change ramp values in part file

    Is it possible for a part file to change the ShopBot ramp values?
  6. Replies
    0
    Views
    329

    Need sample probe point cloud file

    I'm thinking of getting the shopbot probe to probe 3D objects. From reading the forum, it looks like most people import the probe data into Aspire. I'd like to import into Fusion 360. Can somebody...
  7. Thanks, that's what I was looking for

    Thanks, that's what I was looking for
  8. Replies
    1
    Views
    1,135

    How to enable limit switches

    Limit switches work great for X-Y homing, but they don't seem to be enables for jogging round. Is there a setting that enables/disables the proximity switches.
  9. Get absolute position (not work position)

    Is there a way to see what the absolute position is, not the work coordinate position. I don't need it displayed all the time. I just want to move the spindle to a spot and see what the absolute...
  10. Replies
    7
    Views
    1,390

    Thanks, I'll do that

    Thanks, I'll do that
  11. Replies
    7
    Views
    1,390

    I took a closer look at the shopbot and it turns...

    I took a closer look at the shopbot and it turns out the pinon gear on the y-motor was a little loose. I tightening the set screws and it's working MUCH better now.
  12. Replies
    7
    Views
    1,390

    I did grab the spindle and gantry and try to move...

    I did grab the spindle and gantry and try to move them to see if there was any play, I didn't notice anything, but I'll do it again. I have noticed a difference between climb and conv cutting. ...
  13. Replies
    7
    Views
    1,390

    Hole not round

    On the Shopbot (PRSalpha 96-48) at my makerspace, I'm getting holes that are not round. The picture below is about 1.5" diameter. I cut it with a 3/8" end mill. Any suggestions as to what's...
  14. How tram spindle front to back (X-Z plane)

    I'm using the Shopbot PRSalpha 96-48 Model 10216-01 at my makerspace. I noticed the spindle is not vertical from front to back (X-Z place). I know how to adjust left and right by loosening the 6...
  15. Replies
    0
    Views
    671

    Fusion 360 post processor

    I was using the ShopBot at my makerspace (it's been a while since I've used it). I downloaded the latest Fusion 360 ShopBot (openSBP) post processor (ver 42961) from...
  16. Replies
    6
    Views
    1,036

    Need wago connector

    Anyone know the industry part number for the z-zero plate wago connector?

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=34260&stc=1
  17. Replies
    2
    Views
    1,094

    Thanks I'll do a test with the message window.

    Thanks I'll do a test with the message window.
  18. Replies
    2
    Views
    1,094

    VD command in config file

    I was looking at the VD command in the config file:
    ShopBot_PRS96x48alpha.sbd dated 4/23/16

    It has the following:
    VD, 1, 3, 0, 0, 2, 1, 0, .1, 0, 1, 1, -2500, -7500, 8800, 4600, 0,...
  19. Replies
    1
    Views
    976

    Resolution Multiple

    At my makerspace, somehow the config file got messed up and we had to reset our PRS Alpha shopbot. When I zeroed the z-axis with the z-zero plate, it was about 1/4 inch off (plate thickness setting...
  20. Replies
    3
    Views
    1,454

    I see. CN is running the scripts in the...

    I see. CN is running the scripts in the SbParts\Custom\ directory.
  21. Replies
    3
    Views
    1,454

    OpenSBP command - CN

    I'm looking at an OpenSBP post generated by Fusion 360. Can anyone tell me what these two commands do?

    CN, 90
    CN, 91
  22. Replies
    2
    Views
    3,411

    Thanks. I think I'll just delete it from my...

    Thanks. I think I'll just delete it from my version - clean things up a bit
  23. Replies
    2
    Views
    3,411

    MTC.sbp - CHECK_MTL subroutine

    I was looking at MTC.sbp and can't figure out why CHECK_MTL subroutine is there. It doesn't seem to do anything. No matter what, it's going to set &z_adjust to zero.

    First line is commented out. ...
  24. Replies
    2
    Views
    3,300

    Thanks. I was looking at the programming...

    Thanks. I was looking at the programming handbook. I just found it hard to believe it doesn't have ELSE. Also, it seems I can only execute one command after THEN like this

    IF blah blah THEN...
  25. Replies
    2
    Views
    3,300

    OpenSBP - IF - THEN

    Does OpenSBP support IF - Then like this

    IF blah blah THEN
    statement
    statement
    statement
    END IF

    If so, does it also support ELSE?
Results 1 to 25 of 39
Page 1 of 2 1 2