Search:

Type: Posts; User: ken_rychlik

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    21
    Views
    1,217

    If it is consistant about cutting on the edge and...

    If it is consistant about cutting on the edge and not in the center like your last picture, the spoilboard moving has to be the issue.
  2. Replies
    21
    Views
    1,217

    http://www.talkshopbot.com/forum/attachment.php?at...

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=34557&stc=1
  3. Replies
    21
    Views
    1,217

    You should not be using the same processor for...

    You should not be using the same processor for the atc machine that worked on the old prt. Not the post processor anyway. And yes the bit can slip both directions. I'll post of pic of the start...
  4. Replies
    4
    Views
    402

    The main thing you can do when ramping in is...

    The main thing you can do when ramping in is increase the z feed speed. They don't like ramping into a cut with z slower than xy
  5. Replies
    21
    Views
    1,217

    After verifying that it is setting the z height...

    After verifying that it is setting the z height to the correct position, run a file and then check again after the file runs to see if it moved. Bits can slip in a collet sometimes as well. Mainly...
  6. Replies
    4
    Views
    510

    Just fyi, no matter which one you buy, it will...

    Just fyi, no matter which one you buy, it will need to be programmed, even if you get the same one you have now. It may be possible to buy one from shopbot that is already programmed. It is not...
  7. Replies
    7
    Views
    749

    It will work and I have done it many times, but...

    It will work and I have done it many times, but more power never hurts if you want to buy another. I think you would be pleased with the one you have unless you push it very hard, which I doubt can...
  8. Replies
    7
    Views
    749

    Hook up what you have. I think you will do ok...

    Hook up what you have. I think you will do ok with it.
  9. Replies
    23
    Views
    2,316

    I have never measured how much vac it pulls. Two...

    I have never measured how much vac it pulls. Two of them have worked cabinet building on a 4x8 machine for years. If you cut very small parts, you may need to go with 4 motors, or apply both of...
  10. Replies
    23
    Views
    2,316

    http://www.talkshopbot.com/forum/attachment.php?at...

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=34538&stc=1
  11. Replies
    23
    Views
    2,316

    http://www.talkshopbot.com/forum/attachment.php?at...

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=34537&stc=1
  12. Replies
    23
    Views
    2,316

    http://www.talkshopbot.com/forum/attachment.php?at...

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=34536&stc=1
  13. Replies
    23
    Views
    2,316

    Yes. I finished that one up today and am getting...

    Yes. I finished that one up today and am getting it under it's intended machine. Vents to help the motors cool, but not open to where someone can touch the wires. Opposing motors to give room for...
  14. Replies
    23
    Views
    2,316

    http://www.talkshopbot.com/forum/attachment.php?at...

    http://www.talkshopbot.com/forum/attachment.php?attachmentid=34535&stc=1
  15. Replies
    23
    Views
    2,316

    Two motors with mufflers are less than the price...

    Two motors with mufflers are less than the price of one Fein. I have had both. Mufflers are great.
  16. Replies
    1
    Views
    1,144

    This machine has been sold.

    This machine has been sold.
  17. Replies
    23
    Views
    2,316

    Go to central vac and look at the shopbot page. ...

    Go to central vac and look at the shopbot page. I prefer one motor per section over the oem version of several motors per chamber. I'm sure others disagree. I have built about 10 of them. I did...
  18. Replies
    8
    Views
    1,348

    It looks like a Buddy 4x4. Your title may be...

    It looks like a Buddy 4x4. Your title may be throwing some people off. It looks like a good deal for someone.
  19. Replies
    2
    Views
    1,872

    Yes they did. Thanks.

    Yes they did. Thanks.
  20. Replies
    1
    Views
    1,144

    2016 PRS Alpha ATC 5hp single phase

    This is not mine. A friend of mine in Corpus Christi Tx has a 4x8 atc shopbot and wants to sell it. He has the original invoice and it was 44k new. It is in good working condition. He is asking...
  21. Robert, when I said good luck to all, that...

    Robert, when I said good luck to all, that included you. The only thing I "implied" is you are a brand new member.
  22. Not to knock the sale, but a new member, first...

    Not to knock the sale, but a new member, first post, cheap machine.... Be careful about sending money. Good luck to all
  23. Replies
    0
    Views
    589

    Spindle and 20hp Vac

    I bought a used machine that came with a 20hp (220v 3 phase) vac pump for vac hold down. Also it had a 5kw manual change hsd spindle that runs on 380 volts. I can't use either one of them because...
  24. Replies
    1
    Views
    714

    It is not a PRS. It is an older PRT Alpha with...

    It is not a PRS. It is an older PRT Alpha with direct drive motors. Still I think it's a very fair price for what it is. Good luck with it.
  25. Thread: no z axis

    by ken_rychlik
    Replies
    3
    Views
    1,884

    Sounds like a bad driver (red gecko) in the box,...

    Sounds like a bad driver (red gecko) in the box, but here is a test you can do. With everything powered OFF.... on the back of the control box, switch the z and y plugs. Power it back up and the y...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4