Search:

Type: Posts; User: coryatjohn

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    2
    Views
    130

    It could also be that your gantry has been...

    It could also be that your gantry has been torqued. I suggest checking the squareness of your table again. The simplest and most accurate method is to measure diagonal corners. It's far better than...
  2. Replies
    21
    Views
    895

    One possible way to test if the plenum is at...

    One possible way to test if the plenum is at fault:

    1. Cover a zone with thin plastic.
    2. Place a piece of paper in the center of the zone.
    3. Zero an end mill to that piece of paper so that the...
  3. Replies
    21
    Views
    895

    I don't have an ATC so I can't answer for sure......

    I don't have an ATC so I can't answer for sure...

    Did you adjust your zero plate when you skimmed the table? Do the end mills in your ATC carousel have to be re-zeroed?
  4. Replies
    7
    Views
    285

    You could do it as a solid by using an indexer as...

    You could do it as a solid by using an indexer as the hold down. Once a side is finished, manually rotate the fixture with the MB (move B Axis) command and do the next side.
  5. Replies
    1
    Views
    391

    >> ONLY HAS BEEN USED TWICE How sad! Seems...

    >> ONLY HAS BEEN USED TWICE

    How sad!

    Seems like a great deal.
  6. Replies
    8
    Views
    545

    I cut the zero edges of my spoilboard to be the...

    I cut the zero edges of my spoilboard to be the exact zero position. That way, to align a sheet or other material to the table, I just have to get it aligned with the spoilboard edges. Very simple....
  7. Thread: reset error

    by coryatjohn
    Replies
    8
    Views
    492

    >> "keyboard commands to "STOP" seem to be mere...

    >> "keyboard commands to "STOP" seem to be mere suggestions to stop."

    That seems to be a good explanation.

    I'm no expert in the SB internals but from my experience, the stop command (space...
  8. Replies
    6
    Views
    644

    Well, without more information, a valuation is...

    Well, without more information, a valuation is variable. Important stuff such as the date of manufacture, pictures of the control box and unit itself and the Z height would be useful.
  9. Replies
    6
    Views
    644

    It's likely a PRT seeing as how it's 15 years old...

    It's likely a PRT seeing as how it's 15 years old (at least the router is). A picture would answer that question.
  10. Replies
    8
    Views
    596

    For $600, sounds like a good solution.

    For $600, sounds like a good solution.
  11. Replies
    8
    Views
    596

    >> ...but still open to further suggestions. ...

    >> ...but still open to further suggestions.

    Give up on W10 and go back to W7.
  12. Replies
    8
    Views
    596

    When my original controller computer started to...

    When my original controller computer started to die, I went with a "refurbished" Dell tiny computer without a fan and a solid state drive. Bought it on ebay for $150 all in, including W7 and plenty...
  13. Replies
    1
    Views
    246

    I use a Magnate 2709 Surface Planing (Bottom...

    I use a Magnate 2709 Surface Planing (Bottom Cleaning) Router Bit - 3" Cutting Diameter as a planing end mill. Big end mills like this should turn slowly. I use 8k RPM's and depending on the wood,...
  14. Replies
    5
    Views
    436

    The only fire I've had involved a piece of oak I...

    The only fire I've had involved a piece of oak I was milling with a 1/8" cutter. The hold down broke free and the piece moved with the cutter, causing it to stay in the same place for several...
  15. Replies
    1
    Views
    555

    I have a cyclone dust system that works very...

    I have a cyclone dust system that works very well. I never have to wear a dust mask when cutting and there's virtually no residue after a cut. I would be fine with putting one of these machines in my...
  16. Replies
    11
    Views
    919

    What do your chips look like?

    What do your chips look like?
  17. Replies
    2
    Views
    384

    I find redwood to be a very easy material to...

    I find redwood to be a very easy material to mill. It's soft and has a low rate of tearout. A 2-flute downcut, as suggested by dlcw, is a good idea although I've had great results with upcuts. I keep...
  18. Replies
    2
    Views
    712

    I've planed plenty of slabs on my SB and I've...

    I've planed plenty of slabs on my SB and I've found that very little hold down support is required. As long as you don't try and take off 1/4" at a time, all you need do is keep the slab from...
  19. Replies
    20
    Views
    2,275

    Wow! That's an amazing work of art. I'd bet that...

    Wow! That's an amazing work of art. I'd bet that it will still be as amazing in 100 years.
  20. Replies
    4
    Views
    694

    What you're seeing is the characters, like...

    What you're seeing is the characters, like Chiloquinruss said, being encoded.

    https://en.wikipedia.org/wiki/Character_encodings_in_HTML#HTML_character_references

    The above explains it.
  21. Replies
    12
    Views
    1,668

    To be absolutely sure you have the right settings...

    To be absolutely sure you have the right settings for 360 degrees, rotate the indexer 3600 or some large multiple of 360 and see if it ends in the same spot. This will magnify errors so it will be...
  22. Replies
    4
    Views
    635

    Nice job! +1

    Nice job! +1
  23. >> Does the difference in Amps matter or will...

    >> Does the difference in Amps matter or will either of these be OK?

    Both are so close as to make no practical difference. It's the CFM that matters most, and of course the volts. Get the higher...
  24. Replies
    37
    Views
    2,887

    One way you can refine this number is to turn the...

    One way you can refine this number is to turn the indexer 3600 or even 36000 degrees and check the drift.
  25. Replies
    37
    Views
    2,887

    >> Not sure what you are referring to as home for...

    >> Not sure what you are referring to as home for the cut file.

    What do you have set as the start/home position in the material settings? If you're moving off the 0 point for the indexer, then the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4