Search:

Type: Posts; User: jerry_stanek

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    2
    Views
    98

    Here is a file to square your table I have used...

    Here is a file to square your table I have used it several times I got it off the Shopbot forum years ago but still works
  2. Replies
    23
    Views
    1,672

    I use Fien vacs nice and quite and plenty of...

    I use Fien vacs nice and quite and plenty of suction
  3. Replies
    8
    Views
    535

    I use slide bolts for the stops

    I use slide bolts for the stops
  4. Replies
    23
    Views
    1,672

    I like the idea of valves and 4 motors for 1...

    I like the idea of valves and 4 motors for 1 chamber with switches to run 1 2 3 or all 4 motors sometime I need more suction for 1 or 2 zones.
  5. Replies
    6
    Views
    638

    I have seen this unit and it is a PRS

    I have seen this unit and it is a PRS
  6. Replies
    6
    Views
    638

    I think that is a little low. I would start at...

    I think that is a little low. I would start at $11,000 and come down to $10,500 for all that.
  7. Replies
    8
    Views
    606

    Go to setup and you can change the zero plate...

    Go to setup and you can change the zero plate thickness It is under tools
  8. Replies
    13
    Views
    1,354

    The 4G box does not have a contactor

    The 4G box does not have a contactor
  9. Replies
    13
    Views
    1,354

    Still think it is the fan in the power supply

    Still think it is the fan in the power supply
  10. Replies
    3
    Views
    452

    The 2 brown wires go to 24 volt+ the 2 blue...

    The 2 brown wires go to 24 volt+ the 2 blue wires go to Ground and the X black wire goes to input 2 and the Y black wire goes to input 3
  11. Replies
    3
    Views
    452

    Here is a doc from shopbot for my 4G board

    Here is a doc from shopbot for my 4G board
  12. Replies
    13
    Views
    1,354

    sounds like the fan is going out

    sounds like the fan is going out
  13. Replies
    17
    Views
    1,918

    I use a Roll up keyboard and wired mouse with my...

    I use a Roll up keyboard and wired mouse with my computer in a cabinet with filters
  14. Replies
    5
    Views
    770

    I cut ACM and use my wood dust collector for...

    I cut ACM and use my wood dust collector for that. If you branch out into sign foam or Sintra I would go with the Northern one.
  15. He said he was getting an ATC so that means a...

    He said he was getting an ATC so that means a spindle.
  16. Replies
    1
    Views
    550

    You have the machine to make that

    You have the machine to make that
  17. Replies
    23
    Views
    3,030

    If you used a wet saw you could cut the plenum...

    If you used a wet saw you could cut the plenum and a hole saw for the vac hook ups. or just have a counter top maker cut them for you.
  18. Replies
    23
    Views
    3,030

    Have you thought about granite for the base

    Have you thought about granite for the base
  19. Replies
    10
    Views
    1,293

    Here try this file you may have to adjust the...

    Here try this file you may have to adjust the thickness
  20. Replies
    10
    Views
    1,293

    Here is a quick DFX of what Mine looks like. I...

    Here is a quick DFX of what Mine looks like. I pocketed the square .125 and through pocketed the circle you may have to adjust the size of the hole to match you copper cap. I then just wired a clip...
  21. Replies
    10
    Views
    1,293

    you can make your own just get a 3/4 copper cap...

    you can make your own just get a 3/4 copper cap and cnc a corner block
  22. Replies
    2
    Views
    535

    Years ago I added a parallel port pci card to one...

    Years ago I added a parallel port pci card to one of my computers. They are easy to instaal and EBay has them cheap
  23. Replies
    5
    Views
    1,060

    On my one laptop I just had to reload the...

    On my one laptop I just had to reload the firmware for the shopbot to see the drivers.
  24. Replies
    9
    Views
    1,338

    I had that happen to me I had to go back to...

    I had that happen to me I had to go back to 3.6.46 to fix it. Don't know why.
  25. Replies
    3
    Views
    615

    It was working fine 2 days ago today I noticed...

    It was working fine 2 days ago today I noticed the Y dropped out and then when I got the Y back to working by replacing a fuse in the Gecko. The Z and Y work fine alone but the z moves along with...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4