Search:

Type: Posts; User: roy_shimp

Page 1 of 2 1 2

Search: Search took 0.06 seconds.

  1. Replies
    0
    Views
    532

    Service work in NE Florida

    Does anyone do service work in Jacksonville, Florida?
    Rpm controller doesn't work and i may purchase an ATC upgrade to my PRS Alpha I'd need help installing.
    Thank you.
    Roy Shimp
  2. Thread: VFD settings

    by roy_shimp
    Replies
    1
    Views
    4,934

    Kenny - What was the answer to fix the awful...

    Kenny - What was the answer to fix the awful screeching noise? I have that noise and the only thing i have been doing is inputting parameters with advise from the Yaskawa tech people .
    thanks - Roy...
  3. Replies
    0
    Views
    844

    fuzz on pvc letter edges

    I usually use x-cel brand pvc for cutting letters, cuts clean with out fuzz on the edges of letters. Now i'm having a difficult time trying to get the x-cel brand of pvc.
    What brand of pvc sheet do...
  4. Replies
    2
    Views
    1,374

    thanks. i will

    thanks. i will
  5. Replies
    2
    Views
    1,374

    clip art disappears

    i draw a 4x8 work space. i draw a smaller box on the 4x8 work space. on the smaller box i place a fleur de lys . when i run the profile toolpath and press calculate the fleur isn't there.
    what am...
  6. Replies
    0
    Views
    9,196

    rpm controller at keyboard not working

    electricians wired the new prs alpha. think my wiring is right. vfd white wire to c1, brown wire to f1. cycle thru estops then hit reset. go to spindle on. it displays 10,000 which in on the vfd...
  7. thank you, i'm waiting their replys

    thank you, i'm waiting their replys
  8. Thank you. how do you usually make a burr?

    Thank you. how do you usually make a burr?
  9. need help with knowing the strength of two part epoxy

    Does anyone know of technical papers that document the strength of screws in 2 part epoxy? I'll need the data for a sign permit. The intent is to attach 72" z-clip rails ( the rails have screw holes)...
  10. Thanks for the feedback. I sent a report to...

    Thanks for the feedback. I sent a report to shopbot.
  11. thanks - not having that happen before i did a...

    thanks - not having that happen before i did a restart near the closest position and all went well.
    What is a SBHQ report and who at sb do i email it to. thanks again.
  12. shopbot started going real slow in the middle of a Sawatzky woodgrain texture...

    1.5" 15lb HDU, 3/8" Onrud ball nose, nothing strange was happening. I rout this wood grain regularly without problem. Move xy is 4.0, z is 2.0. Jog xy is 4.0, z is 2.0. Columbo 5hp spindle,...
  13. Thread: Old Shopbots

    by roy_shimp
    Replies
    22
    Views
    7,168

    forgot to say thanks

    ... to all of your help. Got it grounded. thanks again.
  14. Thread: Old Shopbots

    by roy_shimp
    Replies
    22
    Views
    7,168

    Thank you.

    Thank you.
  15. Thread: Old Shopbots

    by roy_shimp
    Replies
    22
    Views
    7,168

    think i'm gonna regret asking "what is an earth...

    think i'm gonna regret asking "what is an earth ground (grin)"
  16. Thread: Old Shopbots

    by roy_shimp
    Replies
    22
    Views
    7,168

    Rob - please explain "add a few more grounding...

    Rob - please explain "add a few more grounding cables and run a dedicated earth ground to the frame". What is an earth ground? What would be a step by step? Thanks a million. Roy
  17. Thread: Old Shopbots

    by roy_shimp
    Replies
    22
    Views
    7,168

    Brady x,y and z = .5 ips no dust collection on...

    Brady
    x,y and z = .5 ips
    no dust collection on this small job
  18. Thread: Old Shopbots

    by roy_shimp
    Replies
    22
    Views
    7,168

    Old Shopbots

    Does anyone else have an old shopbot AND does it seem to run well?

    My PRT96 was purchased new in 2000. It has run well, has had upgrades as they became available, had a very picky machinist...
  19. I got side tracked; this post is about chatter ON...

    I got side tracked; this post is about chatter ON THE DIAGONIAL STROKES OF PVC LETTERS.
  20. Brady - I did replace the gears late last...

    Brady - I did replace the gears late last summer, however i will remove the speed bumps. By the way, your explanations on ramp settings have been a great help. Thanks
  21. PRT 96. 5Hp Colombo spindle. I got the shopbot in...

    PRT 96. 5Hp Colombo spindle. I got the shopbot in 2000. Since then (last year) i double checked for rails level and square and had the gantry squared and tack welded.
  22. Chatter on diagonial strokes of pvc letters

    I am still getting chatter on the diagonial strokes of pvc letters. I have read the posts regarding chatter. The chatter also shows up on O's, but not as much. The chatter is on the diagonial strokes...
  23. Replies
    5
    Views
    4,705

    Grain frame or just cnc

    Dick - i have Enroute Pro and although it has woodgrain textures they can take a very long time. However EnRoute also has a tool called Rapid Texture which, what it sounds like is rapid. The...
  24. Replies
    1
    Views
    2,359

    convert Excel 2007 files to .sbp files

    After tweaking a tool path in Excel 2007 i need to save the file as an .sbp file. I can't save a file in Excel as .sbp, so what do i need to do to be able to run it in shopbot ?
    Same question for...
  25. Replies
    10
    Views
    4,882

    Learning EnRoute

    I have EnRoute Pro and some of the tools i have a hard time understanding. My question is how do you folks that run EnRoute learn the tools? Do you call for support? Is there a book? Is there online...
Results 1 to 25 of 31
Page 1 of 2 1 2