Log in

View Full Version : Archives2005


  1. Copy machine question. (1 replies)
  2. Reset drivers??? (1 replies)
  3. Blown fuse (8 replies)
  4. Probe indicator light not lighting (6 replies)
  5. Error message (2 replies)
  6. Cutting differently (3 replies)
  7. Reset table size, squaring Z again, surfacing table (5 replies)
  8. How do you set spindle speed with the Delta VFD (9 replies)
  9. Can't run setup routine -first time, other concerns (1 replies)
  10. Ok, I'm a dummy - how do I... (12 replies)
  11. SB Control Version 3.4.15 problem (2 replies)
  12. Troubleshooting a vacuum leak? (11 replies)
  13. It runs 5,6,7,8,9 cycles, then it doesn't! (5 replies)
  14. LOSING CONNECTION WHEN SPINDLE COMES ON (8 replies)
  15. Indexer (3 replies)
  16. Scaling problem (4 replies)
  17. Lines wont connect (12 replies)
  18. Error 11 "Division by zero" (3 replies)
  19. Other routers that I can mount in my shopbot? (6 replies)
  20. Expansive MDF (3 replies)
  21. No Actual Movement (7 replies)
  22. Blown Driver Board...I think (2 replies)
  23. HELP SHOPBOT DRIVING INTO TABLE (10 replies)
  24. Colombo Collets Breaking (3 replies)
  25. X axis moving in Wrong Direction (4 replies)
  26. Serial Port Failure - Reboot (2 replies)
  27. Blown Z Driver? (1 replies)
  28. Computer freezes up (14 replies)
  29. PRT - jog issues (3 replies)
  30. StairStepped Z-moves (12 replies)
  31. A huge bummer..... (10 replies)
  32. Cutting differently (8 replies)
  33. Problem with move speed settings (10 replies)
  34. Inconsistent z travel (5 replies)
  35. Calibration Issues (4 replies)
  36. Types of mistakes, cut failures. Looking before we leap (5 replies)
  37. Question about E-Stop / Remote Stop on Alpha (6 replies)
  38. Artcampro7 (3 replies)
  39. Cut Issue (20 replies)
  40. Motor tightners (1 replies)
  41. 5 HP Colombo (7 replies)
  42. Z won't plunge into surface (2 replies)
  43. Inconsistent widths and backlash (long) (9 replies)
  44. Router issues (5 replies)
  45. Connection Help (1 replies)
  46. Newbie Qu;ery - Banging carriage setting Z (13 replies)
  47. Router won't turn on new Alpha upgrade (16 replies)
  48. Software and port issues. (3 replies)
  49. Timer Over-run (18 replies)
  50. Limit swich hit (3 replies)
  51. A different kind of HEAT issue (3 replies)
  52. Heat Issues (2 replies)
  53. Trouble with a PR model (1 replies)
  54. Bits burning up (14 replies)
  55. Dialing in my table (23 replies)
  56. 1proximity switch not turning off (9 replies)
  57. Is there somebodi with BERGES inverter (6 replies)
  58. Losing Control Box Connection (4 replies)
  59. What will run on WinXP? (2 replies)
  60. Poor cut quality in plex (9 replies)
  61. Problem with Alpha software???? (0 replies)
  62. Question about possible VA file conversion (1 replies)
  63. X motor makes grinding noise-doesn't move (2 replies)
  64. Driver/Motor Fault Location (2 replies)
  65. Limit Switch lights up but carraige doesn't stop (2 replies)
  66. Zero Plate (3 replies)
  67. FG command question (8 replies)
  68. Outputs on circa 99 PR? (7 replies)
  69. Suppress warning messages (VA,ZT,ST) (11 replies)
  70. Shopbot Software 2.32 (3 replies)
  71. X motors reversing direction at random (17 replies)
  72. LOST KEY COMMANDS IN DOS CUT SOFTWEAR (1 replies)
  73. Need a hand in South Florida (3 replies)
  74. Help for a rookie (11 replies)
  75. SHOP BOT LOSING POSITION (4 replies)
  76. Columbo bearing replacement? (4 replies)
  77. PC ROUTER BEARING REPLACEMENT (8 replies)
  78. Control board intallation problem (1 replies)
  79. Table Surfacing problems (23 replies)
  80. Vectors from illustrator 10 (4 replies)
  81. Clunky Curves (5 replies)
  82. Intermittently losing the controller ... (2 replies)
  83. Where to start (4 replies)
  84. VU (value units) problem (9 replies)
  85. PR Upgraded to PRT -- No Communication with controller (2 replies)
  86. Circle Cutting Problem (9 replies)
  87. Problems with the jogging and moving speeds (1 replies)
  88. Finally up and running but..................PC wont turn off (2 replies)
  89. ERROR "53" (1 replies)
  90. PR model Z axis bearings (3 replies)
  91. Proximity Switches, Sb stops BUT software runs on (12 replies)
  92. Prob Problem (37 replies)
  93. PRTAlpha Control Box Heat (41 replies)
  94. Acrylic Edge Quality (17 replies)
  95. Recovering lost files (30 replies)
  96. Help with stop button (5 replies)
  97. SHOPBOT NOT CONNECTING (5 replies)
  98. Colombo Spindle Noise (7 replies)
  99. Bit deflection-how much is to be expected (46 replies)
  100. Shopbot prt Alpha Problems (37 replies)
  101. Setiing up new shopbot...Router won't power up...Help? (39 replies)
  102. 220V electrical connection to the control box...Need Help! (19 replies)
  103. Comm Break at -0 -1 (5 replies)
  104. European Import (37 replies)
  105. Blown Driver??? (again) (71 replies)
  106. Probe "disconnect" problem (1 replies)
  107. Should there be play in the Vexta steppers? (42 replies)
  108. Bending ABS Plastic (12 replies)
  109. Porter Cable HEAT (60 replies)
  110. Need help with my inconsistant "z" depths (36 replies)
  111. Proximity switch repeatability? (45 replies)
  112. X Motor (16 replies)
  113. Losing steps? (12 replies)
  114. Grounding (49 replies)